If PhieldBug isn’t for you, here are some tips and ideas for designing your own sleeping-trailer – or buying a used one – including some common pitfalls to avoid.
This page is aimed at competent UK DIYers interested in building, or perhaps buying, a small unbraked sleeping-trailer. The page is divided into three parts:
- Secondhand and other purchase options.
- Choosing what to build.
- What to use to build it.
DISCLAIMER/WARNING:
This page isn’t intended as a comprehensive guide. Just an introduction to some of the more popular teardrop styles and methods of construction, and other aspects of amateur sleeping trailer building in the UK.
This page is provided free by PhieldBug.co.uk and without any warranty whatsoever, in the hope that it may be useful.
Any descriptions of the law and legal limitations are merely our best understanding of the law as found at legislation.gov.uk and in other publications: our descriptions may be wrong.
Contents
Buying Secondhand or Bespoke
Before designing your own, you may be looking at second-hand, home-built, and one-off bespoke options out there. There are some lovely second-hand sleeping trailers on the market. But there are also pitfalls aplenty for a first-time buyer.
Secondhand Commercial Teardrops
Over recent years quite a few teardrop startups have come and gone, some leaving behind a legacy of secondhand trailers which still come on the market. A few teardrop makers still exist in the UK, some producing in quite large numbers, and these are frequently available secondhand.
Such pre-owned trailers can be well worth seeking out, with considerable savings on price. We notice, too, that buyers of teardrops from the larger manufacturers sometimes tire of their new trailers quickly and sell them on within a year or two: buying one of these can save joining a waiting-list for a new one.
Bespoke New Homebuilds
A few individuals build one-offs to-order, and to the buyer’s specification. They work mostly in their garden sheds, though we’ve seen fewer and fewer of them advertising in the last few years which either means they have more business than they can cope with… or that they’ve given up.
Amateur Homebuilds
Many, many amateur homebuilt teardrop trailers have been constructed in the UK. The quality of these varies from superb to need-a-longer-bargepole.
Weight and Weight Distribution
The first significant issue with bespoke and home-built trailers – and even some manufactured ones – is their weight. A heavy teardrop is an oxymoron: the user has to handle the weight of a caravan, yet without enjoying the benefits of a caravan’s space and facilities. Lightness is key to enjoying the teardrop experience.
Check the weight stated on the trailer’s TIN-plate (usually fitted on the drawbar) – although this is only the gross weight so does not tell you the all-important empty weight. Try moving the trailer by hand to assess its empty weight, and compare with trailers of a known weight that you have viewed.
Beside being unpleasant to use, a heavy teardrop may also be illegal to tow. For most full licence holders the maximum unbraked trailer weight (including the weight of the load on the trailer) allowed to be towed in the UK is (and see our disclaimer/warning at the top of this page):
- Motorcycle over 125cc without a sidecar: 150kg, or half* the kerbside weight of the motorcycle, or the maximum stated by the manufacturer, whichever is less. Motorcycles also have severe restrictions on the trailer width and length. (*If the trailer has brakes, then two-thirds.)
- Motorcycle with sidecar: same as trike, below.
- Trike: 750kg, or the maximum stated by the manufacturer, or half the kerbside weight of the trike, whichever is less. A trike is not allowed to tow any trailer which has an unladen weight of more than 254kg*. The latter requirement rules out many teardrops. (*The 254kg limit applies even if the trailer has brakes.)
- Car/van/motorhome: 750kg, or half the kerbside weight of the tow vehicle, or the maximum stated by the manufacturer, whichever is less.
- A vehicle manufactured on or after 1st August 1998 for which the manufacturer has not specified a towing weight limit: the vehicle is not allowed to tow a trailer. A towbar may be fitted but only for use as a load-carrier – for example for cycles.
- Other classes of vehicle: there are other classes of road-legal vehicle in the UK. Most are either specialised (e.g. steam traction engines) or are unlikely to practical for towing a teardrop, even if allowed to (e.g. light quadricycles), or cannot tow at all (e.g. motorcycles under 125cc).
It is worth, before traveling to view any trailer, finding out that trailer’s empty weight and comparing it to the towing limit for your vehicle, with consideration for the additional weight of bedding and other typical trailer contents.
Check also the noseweight: on many trailers the axle is positioned fashionably rearwards, resulting in an excessive noseweight which will be greater than the maximum downforce permitted on many tow vehicles’ hitch fittings. A high noseweight will also make manoevering by hand – especially on soft ground where the nosewheel may dig-in – very difficult. Noseweight gauges are widely available and we would recommend taking one when viewing any trailer whose noseweight is not documented.
Materials
The second major issue with bespoke and home-built trailers is their construction, especially if they are built from sheet timber materials like plywood.
If the trailer uses plywood for construction, check for delamination. If any delamination is found, then walk away: the wrong type of plywood has been used and the problem will only get worse.
If the trailer’s structure is built from builder’s ply, or from OSB, or from any other ‘moisture proof’ board – even if it has a seemingly weatherproof exterior such as rubberised paint or aluminium – then it is unlikely to be suitable for storage outdoors in the UK climate. So unless you intend to store it indoors except when in use, do not buy.
But do not write-off all teardrops which are constructed from plywood: if marine plywood has been used, then it should be fine.
Damp
The next issue is damp. Many sleeping trailers suffer from damp, due to internal condensation. Almost the only exceptions are those built with significant amounts of fixed ventilation. If there is much smell of mould inside then find the source of the damp which has triggered the mould. A secondhand mouldy trailer will be a gamble to buy: maybe fitting additional ventilation will be sufficient remediation, or maybe the mould is deep in the structure and cannot be suppressed.
Check the doors, windows, and ventilators for watertightness. If doors and windows rely on rubber seals, check that the seals are properly compressed when the door or window is closed. Check that there is enough ventilation and that the fitted vents won’t admit heavy road spray or wind-driven rain – it only takes the entry of half a cupful of water to make a bed uninhabitable on arrival at camp.
Home-Built Trailers
If the trailer appears to be a one-off home-build, then also check it against the issues raised in the rest of this document below, under Design Matters and Construction Methods And Materials. Bear in mind that home-builders generally have no experience of teardrop building when they start and, as the saying goes “experience is what you get… just after you needed it”. Many – but not all – home-builts therefore suffer from multiple issues. Many, many home-built trailers are flat-out illegal, either because they do not meet minimum lighting (or other) standards or – very commonly – because they have not been registered. See The Law, below.
Online Resources, Plans, Kits
There’s a lot of teardrop chat online. The vast majority of it relates to American teardrops which tend to be heavy, have the axle far to the rear (for off-road use and for towing with large vehicles), and are generally not designed with the UK’s climate and typical family cars in mind. Materials and material sources that are readily available in the US are often less available in the UK. When researching for your own design, it is best to concentrate on trailers which have been successful in the UK.
Plans
CDs, DVD-Rs, downloads, and USB-sticks crammed full of teardrop construction plans are constantly listed on auction sites to purchase for a few pounds. Almost all of these are ancient designs, long past their best-before dates, and will be of little relevance to a modern self-builder. Many don’t even include photographs of completed examples, so may be merely imaginary with not a single example ever built. Save your money.
Kits
Kits now seem fairly rare on the UK market. Perhaps this is because most self-builders are enterprising folk, already with considerable workshop experience, who prefer to plough their own furrow.
Some kits are only partial, in that they build a single-skin box trailer, possibly with a door, but without windows, insulation, or interior. These finishing stages are at least as much trouble for the builder to design and complete as the shell itself, so a prospective buyer of such a kit should consider carefully whether the purchase price of a partial kit justifies the limited benefits on offer.
A good kit – which builds a complete ready-to-use trailer – can save the builder a great deal of trouble: the kit supplier will have ensured that the finished trailer is practical and legal. The kit supplier should also have built many examples during the development phase, giving themselves the opportunity to refine the design and materials so the weight is minimised, and any snags are ironed out. A good kit will assemble straightforwardly, with minimal trouble, resulting in a well-ventilated, waterproof, insulated, and durable teardrop that relieves the builder of the need to do their own R&D on materials, adhesives, coatings, and designs. In short, a good kit can save the self-builder a huge amount of money and vastly reduce the time lost to mistakes and re-starts. But this is only true if there is a kit available which produces the style, and size, of teardrop that the builder requires.
Repurposing Other Trailers
It may be tempting to repurpose a box-trailer or a horse-box or other similar trailer, by fitting doors and windows. Such trailers are designed to lug large loads so are extremely heavy and usually also have brakes. They’re also unlikely to be completely watertight. These make a very poor starting-point for a sleeping-trailer.
The Law. Boring… Until You Lose Your Licence
There has been – and continues to be – a lax attitude to trailer construction law in the UK. If you are viewing secondhand trailers, chances are you will come across many which are not legal for use on UK roads. This is partly from poor communication of the legal requirements. Some drivers only discover they’ve been breaking the law when they’re stopped on the road, and clobbered with a heap of points for their trailer’s multiple violations. However, ‘not having a clue about it’ won’t reduce the number of points you’re awarded. This is especially galling if you’ve bought a secondhand trailer in good faith, and are later stopped and fined because it has been illegally constructed.
Fortunately, the UK has a long history of self-built road vehicles, and the government is reasonably supportive of it. So the law relating to home-built trailers has been made accessible to the lay-person. The DVSA documentation supplied to IVA inspectors gives an excellent summary. Our PDF attempts to summarise the key requirements a teardrop must meet.
IVA and Pre-IVA
All new trailers – unless built by large manufacturers to a type-approved design – must be registered and go through an IVA. This is an inspection by DVSA which checks that the trailer is built to UK regulations and is safe to use on the road. Although the IVA inspection is somewhat like an MOT, an IVA is not an MOT: it is a one-off type-approval for a single vehicle (hence the name ‘Individual Vehicle Approval’.) On passing, a certificate is issued which should be kept with the trailer.
Any bespoke or home-built second-hand trailer, which does not provably have an IVA, is unlikely to be road-legal. The only exception is if the trailer was built before 29th October 2012, when trailer IVAs were first introduced.
Any second-hand trailer – whether from a large manufacturer or a home-builder – should display its maximum gross weight. Any trailer built from 1997 must also show the date of manufacture. Any trailer built after 2012 must also display the maker’s name, axle weights, and a TIN (essentially its serial number). A trailer which doesn’t even meet these modest legal requirements shows a cavalier attitude to the build, and should be viewed highly skeptically.
All glazing on any second-hand sleeping-trailer must be E-marked, irrespective of the trailer’s age. If the glazing is not E-marked then, again, the entire trailer should be viewed with a skeptical eye.
If the trailer looks only a few years old, yet has a claimed build-date before 2012 (or even has no build-date) then be extremely suspicious about such a pre-IVA claim: it is possible that the builder has pre-dated a recently-built trailer – or not dated it at all – to evade obtaining an IVA. And since obtaining an IVA is both cheap and simple, that would imply that the builder does not have faith that the trailer is up to the standard required to be used on UK roads. The best option with such a trailer is to walk away: using it without an IVA would be an automatic traffic offence – possibly with further multiple offences when incorrect construction and/or lighting have been taken into account. And in event of an accident – irrespective of actual blame – you would likely be deemed at-fault. Your car insurance may even be voided.
There is no online information for trailer registrations (unlike for cars) so a buyer cannot look up a trailer’s IVA status. So if the seller claims the trailer has an IVA but they have lost the IVA certificate, then buy only after a duplicate certificate has been purchased by the seller from DVSA. Buying an un-approved secondhand post-2012 trailer with the intention of obtaining an IVA for it may prove challenging: the IVA system is set up to deal with newly built trailers, not secondhand ones.
If the trailer is genuinely pre-2012, and has no IVA or type approval, it remains your responsibility to confirm that the trailer meets the UK regulations and is safe to use on the road. In particular, the presence and positioning of the correct lights and reflectors, a sufficiently strong chassis and suspension, correct glazing types, and a plate stating the trailer’s year and weight. You should be very wary of buying such a trailer unless you are sure it meets legal minimums because, again, using an incorrectly built or lit trailer would be a traffic offence(s). And in event of an accident – irrespective of blame – you would likely be deemed at-fault.
Modifications
A trailer may have originally been sold with an IVA or a type-approval, but a subsequent owner has modified it. This can void the trailer’s approval.
The most common mod is to change to wider wheels – often to match the towing vehicle. This seems innocuous but isn’t: the resulting trailer is wider than designed which can easily result in the lights and reflectors being incorrectly positioned – and in some cases even that some extra newly-necessary lights are not present. In addition, the replacement wheels may impose additional stress on the chassis and suspension, potentially leading to catastrophic failure.
Other, more extensive, modifications are also common: roofracks, awnings, additional hatches, drawbar boxes, cycle carriers. These can all potentially reduce structural integrity, overload the chassis, and/or void the approval.
Size, Weight, Lighting
There are numerous regulations which limit the size and weight of trailers. These vary depending on the tow vehicle manufacturer’s limitations, the tow vehicle’s weight, the tow vehicle’s type (bike, trike, car, van) and the driver’s licence. You should know these limitations before setting out to build, or buy, a teardrop trailer.
There are strict regulations about the lights and reflectors which must be fitted on the rear, sides, and front of a trailer. These vary depending on the trailer’s size. They also vary depending on the type of trailer (boat, box, caravan.)
Design Matters
Building your own – rather than buying new or used – means you are absolutely free to make any design you please, within the limits of practicality and the law. We haven’t set out here to tell you what to design, nor even how to design it. But below are a list of the matters which any designer must consider, in order to come up with a useable – and achievable – design.
What Teardrop Means
‘Teardrop’ means a huge variety of things. Manufacturer ‘Tab’ make classic-teardrop shaped trailers which are as fully specified (and as big and as heavy) as a caravan, with room inside to stand, and separate furniture for sitting, sleeping, and cooking. Manufacturer ‘SL Industries’ make little trailers with just enough internal floor area, and headroom, to lie down or sit up in. These are just examples which are near the opposite ends of the spectrum of the wide range of manufactured sleeping trailers available in the UK. There are many other commercial variations on the teardrop theme, varying in size, style, level of specification, build quality, and – of course – cost.
This web page is most relevant to small to medium sized trailers, and begins to be less relevant for designs which are so large that an average adult could stand inside.
Shapes
The most common style of sleeping trailer is rectangular in planform, with flat and parallel vertical sides, and a flat floor which is just large enough for a bed. Within this limited style, there are two basic shapes: classic-teardrop (‘spam-can’) and squaredrop (cuboid). The names describe the shape when seen from the side. Classic-teardrops are generally the more aesthetically pleasing, while squaredrops can be built more easily and using a wider range of materials, including rigid boards.
In-between are half-moon shapes, and shapes with square ends and flat roofs but with one or both top corners rounded-off. These have limited appeal for the self-builder, being not as aesthetically pleasing as a true teardrop yet still requiring the construction of curves, which are more difficult to form than simple angled corners.
There have been unusual, interesting attempts to break away from the ‘floor, two sides, and a roof’ pattern for teardrops. We have spotted…
- Geodesic-domes.
- Tapering sides.
- Wedge shapes.
- Multi-faceted sides and, sometimes, roof.
- Steampunk styling.
- ‘Wagon’ shapes – a roof curving from side-to-side.
- Bow-fronted – a curved ally front sweeping into straight sides.
- Pop-up tops – with solid or fabric expanding walls.
- Extensible (longways) and expanding (widthways) trailers
- Access/egress via a rear door (or curtain in the case of pop-tops).
Here, we’ll just call all small sleeping-trailers ‘teardrops’.
Usage
At the start of the design process the first questions to ask are, of course, who is going to use the teardrop and how will they use it? Children would require less space than adults. Some adults will require less space than others. A solo camper will require less space than a couple… though not necessarily always.
And what vehicle will the teardrop be used with? A teardrop intended as an extra bedroom for a motorhome can be less complex, and possibly smaller, than one that is used behind a car as the main accommodation and so has to provide more amenities.
A teardrop is typically used for sleeping. But it is worth, right from the start of the design, considering the other uses the trailer will be put to: sitting to eat, sitting to watch TV, reading, using a laptop, and getting dressed. And also cooking, though usually this will take place under an external awning or – somewhat less comfortably – in a rear hatch ‘kitchen’. Storage should also be planned.
Sitting
In most small teardrops, the occupants will sit on the floor (the ‘bed’) facing rearwards.
Internally, a vertical end-wall would be unpleasant to sit against: a sitter requires a reclining seat-back. This is simple to achieve in a classic-teardrop – the sloping shape of the front of the pod automatically creates a reclined seat-back. In a squaredrop a separate reclined seatback can be built against the straight front wall, but space for it to encroach onto the floor must be allowed for, and any external side door must be positioned to clear it.
Sleeping
When sleeping, the ‘foot’ end of the sleeping area doesn’t require as much height as the ‘head’ end… this is where the classic-teardrop shape originally derives from, saving structure and weight where it is not required.
Dressing
Getting dressed requires surprisingly little space – and certainly most people can dress without having to stand.
Storage
Cubbyholes or cupboards built against the interior front wall of the pod are handy while sleeping… but again they require clever design if they are to be comfortable to lean against when sitting.
Internal storage at the rear of a small pod – beyond the ‘foot’ end of the bed – is likely to be impractical unless it can be accessed from outside: trying to reach that end of the pod from inside would involve uncomfortable contortion unless the roofline is high all the way to the back of the pod.
Cupboards are unlikely to be practical along the side of the pod unless the pod is exceptionally wide.
The space above the ‘foot’ end of the bed is generally unused by occupants. So storage can be fitted here to make use of otherwise wasted volume inside the teardrop. Such storage could be designed to be accessed internally. Or it could be screened from the inside and instead made externally accessible via a rear hatch. The choice of access depends on what might be stored here, but see notes on vertical weight distribution before designing storage for heavy items. Our preference is to fit a large internal shelf, where the occupants can stow their day-wear while sleeping, and where bedding can be stowed in daytime. Small racks, to the sides of the shelf, can hold evening essentials such as snacks, earphones, books, charging cables, and reading glasses. The front edge of the shelf can carry a mount for a smartphone or iPad, for comfortable web browsing and TV viewing.
Size and Weight
A teardrop trailer is implicitly small, typically having an accommodation volume of 2-3m long, 1-1.5m wide, and 1-1.5m high.
For a simple sleeping-trailer teardrop, the pod’s width is the most important variable to consider. The minimum width that suffices for two people is approximately the width of a double bed – or a little less after allowing that the very edge of a double bed is unuseable due to the risk of falling out, whereas there is no such risk in a pod. Some particular justification would be needed to design a pod that is wider than the tow car, as it then becomes more trouble to use on the road: it requires towing mirrors, the exposed frontal area increases drag and increases fuel consumption and decreases vehicle performance, and it is difficult to park it in a normal parking space.
As for pod height and length, a trailer that is high enough to sit up in, and long enough to lie down in, is the minimum to be adequately comfortable. Extra height, greater than that needed to sit, won’t much increase comfort unless the height is sufficient to stand – at which point the trailer is verging on not being a teardrop any more. Extra length, greater than that needed to sleep, will only be beneficial if it is used for something practical such as cupboards.
The ideal teardrop size, then, is just big enough, and no more.
So a teardrop is smaller – usually much smaller – than a caravan. But unless the weight is also similarly reduced there’s very little benefit to having a teardrop. A lightweight trailer will be pleasant to tow, easy to move around, and easy to pitch on a campsite. A target empty weight of 250kg, with a noseweight of 15-25kg, would be reasonable. Less would be better. A trailer over 400kg, and/or a noseweight over 40kg, will be difficult to move, less pleasant to tow, and will not compare favourably against an ultra-light small caravan which would offer far more amenity at close to the same weight.
There are legal – and safety – limitations on the maximum weight that any vehicle can tow. The lighter the trailer, then the more tow-car options that are available.
Aerodynamics
Nominally, a classic-teardrop creates less drag than a squaredrop. But on tow, this consideration barely applies: the towing vehicle will so disturb the air that the trailer’s shape will have only modest effect on the total drag. A far more important factor than aerodynamics, when it comes to performance, is weight: the heavier the trailer then the more power will be sapped from the tow-car, particularly when accelerating or climbing a slope.
That’s not to say that shape is unimportant aerodynamically. In particular, a lightweight trailer will be prone to disturbance by side-winds. This is particularly important in three situations: on a motorway when passing a large vehicle; on exposed roads in windy conditions; and when camping in windy conditions. In each case, a light but large trailer will move uncomfortably. Minimising the side-area and the height of the trailer – especially behind the axle – will significantly reduce the effects of side winds. So a classic-teardrop, or a wedge-shaped (blunt end forwards) squaredrop, will be beneficial.
Doors, Windows, Ventilation
Doors
Door(s) should be positioned so that all occupant(s) have ease of access and egress, when using the trailer for seating and also for sleeping, preferably without forcing any other occupant to move.
It is generally better to position the doors forwards of – rather than behind – the axle: this allows entry into at least the forward part of the trailer while it is freestanding, even if any rear supports are not lowered.
Often, for economy of build, only one side-door is fitted but this is inevitably impractical when there are two occupants unless the trailer is unusually large. If there is any likelihood that the trailer will be used in hot weather then one door – even paired with a ventilator on the other side – is unlikely to allow adequate cross-draught.
Doors should ideally have at least a childproof lock, to prevent children playing inside the trailer when it is parked without its steadies or legs extended, and so at risk of tipping suddenly if a person moves to the rear. Door locks should always be openable from the inside, even when locked: otherwise someone may be trapped inside – potentially in dangerously hot weather – by an accidentally slammed door. Similarly, a door which can be locked from the inside, preventing even a keyholder gaining access from outside, would usually be an undesirable feature if children are using the trailer.
A clip or magnetic catch to hold a door open in a breeze is useful.
Windows
Windows are often something of an afterthought, but large untinted windows make wet days stuck inside more bearable so should be considered early in the design.
Windows are about more than admitting light. Most seated occupants will prefer a window they can look out of while seated, and this requirement tends to position the window in the same place as the door – at least on small trailers. A simple glazed door, with no other windows needed, means fewer components to purchase and fewer exterior fittings to make watertight.
A fixed window in the roof, allowing a view of the stars, is an attractive notion but be cautious about having large single-layer uninsulated areas of roof which may attract condensation. In any case check that E-marked glazing will be available in the size you intend to fit. Any roof glazing would require shutters or blinds. A large glazed roof area would benefit from an external reflective insulating blanket, to prevent excessive solar heating gain during the day.
DIY double-glazed windows are likely to be a design feature too far. The effort involved may far outweigh the intended benefit. A DIY sealed unit is extremely difficult to make without condensation forming internally. A non-sealed unit (i.e. one with a removable or hinged inner layer to allow the glazing to be dried and cleaned) will be complex and bulky.
All glazing will require shutters or curtains.
Fixed ventilation
Permanent ventilation is crucial to condensation control. And sufficient permanent fixed ventilation is essential for guaranteeing adequate fresh air to occupants. Fixed ventilation should be installed in such a way that it cannot be shuttered or accidentally blocked. Insect-proof mesh in the ventilators is important for comfort – internal lighting will attract insects to the ventilators at night.
A fixed vent(s) low down, in combination with fixed vent(s) high up, will automatically cause air to be replaced in hot weather: the hot interior air exiting at the top and cooler external air being admitted at the bottom. Positioning the low and high vents at opposite ends of the trailer forces replacement of the entire volume of air in the trailer, rather than just the area near the vents. But avoid placing the low vents where they will cause a nuisance draught: too near to head or feet for example.
Forced ventilation – using for example an ultra-quiet 12V computer-case fan to suck air in (or out) of a fixed vent – could be useful for keeping cool in hot weather, especially if insects make it impractical to leave windows and doors open.
Opening ventilation
Additional opening ventilation, to allow a strong through-draught, is essential to quickly cool a trailer after a long day in the sun when even the best-insulated trailers will have become hot. Again, two doors can easily provide this.
An opening rooflight vent can be useful, though certainly not essential, for keeping the sleeping space cool, but none on the market are visually elegant.
Water ingress
All openings and vents should, of course, be completely watertight against rain. They must also be completely watertight even when the rain is driven onto the pod during high speed travel. And they must be watertight against driven spray from other vehicles’ wheels which may splash – at high velocity – against the trailer from almost any direction – sideways and even upwards.
A fixed vent, directly penetrating from the outside to the inside, risks admitting water even if covered with a downward-facing external grille. Such vents should instead slope steeply upwards within the wall of the trailer so that the openings are staggered, with the internal one higher than the external one.
Hinges
All openings should, in general, be hung with the hinge forwards or upwards, so that if the catch fails while on tow, the door or window won’t be flung open – and possibly destroyed – by the passing air.
Door hinges, in particular, would usually be vertical, unless gas-struts or similar are used to help control the door. A sloping hinge – in any direction – will result in a door which has a tendency to rotate itself under gravity, the direction depending on which way the hinge leans. A gull-wing door may present a hazard when open, and its short hinge-line may make it vulnerable to damage.
Rear Hatch and Kitchen
A very popular addition. Certainly a rear hatch with a kitchen in it is an appealing and romantic notion… when the sun is shining. But think carefully before embarking on a rear hatch, and even more carefully before fitting a kitchen into it. Only proceed if you answer ‘yes’ to all the following:
- You don’t mind adding enormous weight and complexity to your trailer.
- You’re happy to risk rainwater leaks, especially at speed in wet weather.
- You prefer to stand when cooking.
- You don’t mind cooking outside in the rain.
If your teardrop is to be towed by a campervan or motorhome, then a second kitchen would be excessively luxurious anyway.
If your teardrop is being towed by a car – especially a hatchback – consider fitting the kitchen, as a lift-out unit, into the back of the car instead. Not only does this add flexibility – being able to cook in the open hatch, or moving the kitchen under an awning by the teardrop – it also means the kitchen can travel with you when away from the teardrop, to a remote seaside cove or a high mountain car park where there might be no amenities, for example. On a day-trip, a traveling kitchen easily beats a pack of sandwiches and a Thermos.
Shape Variations
Avant-garde pod styles shouldn’t be excluded, but they should be approached with caution due to the engineering challenges they present.
Sloping sides
Building a pod with sloping sides, so that the roof is narrower than the floor, reduces weight and aerodynamic drag without reducing floor size.
However, any doors and windows set into sloping sides will also slope. Performance of water seals will become critical and, even if the seals are perfect, water-drips when doors are opened will be almost inevitable. An awning would therefore be virtually essential.
Door hinge-lines will slope, resulting in the door having to be lifted to open it, although it will also hold itself open under its own weight when opened to 180 degrees.
Tapering Sides
A sleeping-trailer which is wider at the front (the head of the bed) than the rear (the foot of the bed) could be just as comfortable to sleep in – especially for a solo occupant – as a trailer with parallel sides. And it makes good sense both from weight-saving and aerodynamic perspectives. The only drawback we can see is that it would require a specially shaped mattress which would limit the options available.
A refinement on this would be a shape that tapers towards the occupant’s shoulders both from the front and from the rear. Again, further weight savings and better aerodynamics, especially if the sides are gently curved from front to rear. There may, however, be a risk of the trailer having a coffin-like appearance, moreso if the roof and/or walls were angular.
Facets and curves
Doors and other openings set into structures with multiple faceted sides, or with curved sides, will generally be shaped also with facets and curves to match the sides. These may be difficult to fabricate accurately and even more difficult to make watertight. The hinge design must allow the hinges themselves to be exactly co-linear, as well as allowing clearance for the shaped edge of the opener to clear the shaped bodywork. Most vehicle door hinges have the same challenge. An examination of these – particularly classics which often use simpler external hinges – may help with hinge design.
Pop-up roof
One particularly clever design we have seen – from a manufacturer now sadly closed – was a clam-shell pop-top hinged at the front. When open, a curtain of tent material with a sewn-in fabric door provided access.
Other pop-top styles are possible. Numerous folding and pop-top caravans and campervans offer inspiration.
Any walls which expand vertically – whether solid or fabric – must be designed with great care so that water falls away from any joins, rather then pooling or running inside.
Single-skin expanding walls – and especially if they are fabric – will attract condensation so even higher levels of fixed ventilation will be required. Breathable fabric is widely used on small single-skin tents and can overcome condensation, provided the living volume is compact.
Entensible and expanding pods
A few teardrops have been built which can expand lengthways or widthways. Many caravans, and a few campervans, are in production with such features.
The critical issue is making the sliding joint watertight, both on the road and when pitched, and we’ve not yet seen any teardrops get beyond prototype. Potentially, a lifting rear hatch could conceal (and shelter from water) an extension which telescopes out from underneath it when the hatch is open.
Folding pod
The exceedingly clever ‘Wide Path Camper’ is the only solid-walled example of this we have seen. While the Wide Path is designed for bicycles, it is surely the best inspiration we’ve seen for a motorcycle teardrop design which could meet the stringent trailer size requirements in the UK and yet be long enough to sleep inside.
Chassis
Platform vs A/T-Frame
A teardrop comprises of a pod, an axle (or two stub axles), and a drawbar with hitch. Almost invariably, the axle and drawbar are built together as part of a steel chassis, with the pod built atop.
The chassis may be a platform type – typically rectangular – onto which the floor, sides, and ends/roof of the trailer are directly mounted as independent components, jointed and sealed against water ingress. In this design, the chassis lends its strength to support the whole floor of the pod.
Alternatively – but much more rarely – the chassis may be a simple A-frame or T-shape, supporting the pod only across the middle of the floor and at the front of the floor. In such case the pod must have sufficient structural integrity to support itself – including large areas of its own floor – without an underlying steel structure. Typically this means constructing a monocoque pod, whose floor, roof, and walls are tightly bonded to form a single stiff structure.
A platform chassis is commonly chosen by first-time builders. But while a platform has considerable strength it has only limited rigidity, especially in torsion. So unless the pod itself is sufficiently rigid, the entire trailer will twist when in use. This will cause movement of pod joints, opening water leaks.
A platform chassis cannot, therefore, be relied upon as the main stiffener for the trailer: the pod always has to provide the torsional stiffness. But… if the pod is built to provide the essential structural stiffness that the chassis lacks, why then also add the weight of a platform chassis?
Drawbar
The drawbar is a key element of the trailer and it is vital that it be adequately specified. Select a steel section which can tolerate all the forces imposed on it: towing loads, side loads, and the repeated up-and-down forces which will be imposed by the trailer ‘nodding’ while being towed. Drawbar failure while towing would be catastrophic, so consider having the drawbar design checked by a competent structural engineer familiar with road vehicle design.
If a drawbar load is to be fitted – such as a locker or a bike rack – then the drawbar will require even more strength.
Drawbar length
Given that a teardrop is intended to be compact, its drawbar should be as short as possible. The absolute minimum length is dictated by the tow-car: the drawbar must be long enough that there is clearance between the corners of the car and the front of the trailer (or any drawbar load), when the car is driven on full steering lock, allowing a generous margin for movement of the suspension and bumps on the road surface.
Additional considerations include allowing room for the car’s tailgate or rear doors to open when the trailer is hitched, although sometimes the nose-leg / jockey-wheel will block a particularly low-threshold tailgate from opening anyway.
The shorter the drawbar, all other things being equal, the greater will be the noseweight. So drawbar length must be decided on before choosing the axle location.
Occasionally, pictures of teardrops with enormously long drawbars – usually also with the axle positioned close to the rear of the pod – surface on forums. We have seen drawbars so long they almost double the trailer’s length. In all likelihood, the builder has either started their build on an unsuitable chassis (an A-frame from a caravan for example) or they have extended the drawbar in order to reduce the noseweight: its extra length effectively giving greater leverage to lift up an excessively forward-positioned centre-of-mass of the trailer. Apart from the pain of having to park with, and winter-store, such a long trailer, cornering will also be compromised as the wheels of the trailer will turn well inside the wheels of the car, risking kerbing or even striking other vehicles, especially in tight places such as car-parks. Pitching on any significant slope will also be difficult, as the nose-leg / jockey-wheel will run out of adjustment before the slope has been compensated for. This type of design is to be avoided for normal road use.
Suspension, Wheels, Brakes
Suspension and tyres should be appropriate to the weight of the finished trailer. Over-specifying either will result in the trailer being excessively bouncy while being towed. Correct inflation pressures can be calculated using a simple formula involving the weight of the trailer, the maximum rated load for each tyre, and the maximum rated pressure of the tyre. If the resulting calculated pressure is much under a minimum of 20psi then the tyres are over-specified for the job. Beware online tyre-pressure calculation tools: most have a built-in minimum tyre pressure. Some even use the wrong formula.
Brakes are a headache worth avoiding. Prefer instead to build a trailer light enough that your car is permitted to tow it without needing the trailer to be braked. Weight, complexity, cost, maintenance, and likely future legislation requiring testing of braked trailers should be sufficiently off-putting.
Axle Position
A critical chassis decision is where along the length of the trailer to position the axle, which will then determine the noseweight of the trailer. If at all possible, leave the choice of axle location until after the pod is completed. Otherwise you may find yourself with a trailer that is far too heavy – or too light – on the nose.
Ensure the doors do not foul the wheels or mudguards, and allow for the possibility that the wheels will need to be further forward than you expect, in order to attain the correct noseweight.
When using ‘Indespension’ style units, note that the effective axle position is where the wheel-hubs of those units are. This is typically 75-100mm rearwards of the suspension mounting-plates.
Hitch Height
A modern car – when laden – must have a hitch height between 350 and 420mm from the ground. When the car is unladen the actual hitch height will usually be higher and on some modern vehicles – such as pick-up trucks – it will be hugely higher.
A new-build trailer – unless designed for off-road use – is legally required to have a hitch height between 385mm and 455mm from the ground, when the trailer is level. It is generally best to aim for the lower end of this range so that – in most circumstances – the trailer will be more-or-less level when hitched to a typical modern small or medium sized car.
An ’emergency’ increase in hitch-height can be achieved by swapping a pressed-steel hitch for a cast hitch. On a square 50mm drawbar this will raise the hitch-height by about 50mm. The consequential change in loading conditions of the drawbar should be considered before doing this.
Weight and Weight Distribution
As noted above, noseweight is a prime consideration. The common recommendation for large trailers – especially caravans – is 5%-7% of the total trailer weight. But for a very lightweight trailer 10% is a reasonable target. Less than 5% will be dangerous to tow. A weight in excess of the tow-car’s maximum allowed towball downforce will be illegal. A noseweight more than 10% will be awkward for a user to move around on the campsite – likely too heavy to pick up and also so heavy that it compresses the jockey-wheel into any soft ground.
There is much more to weight distribution than noseweight, however. It is – sadly – easily possible to create a trailer which has a sensible noseweight but which is horrible to tow and difficult to manoever by hand.
Fore-and-Aft Weight Distribution and ‘Nodding’
The further that any weight is installed from the axle (forwards or backwards) the more it contributes to the rotational inertia of the trailer. So a trailer with a large mass positioned on the axle will have a low rotational inertia. A trailer with that same mass positioned with 50% on the drawbar and 50% in the tail of the pod will have a high rotational inertia.
With the nose of such a high-rotational-inertia trailer attached to a vehicle, a spring/mass oscillatory system is created. When driving on all but the smoothest roads this can lead to the trailer ‘nodding’ fore-and-aft, while simultaneously bouncing the rear of the car up-and-down. This puts great strain on the trailer’s drawbar and is uncomfortable for the car’s occupants.
The higher the rotational inertia of the trailer then the worse the nodding will be. So a heavy trailer will be worse than a light trailer. And a trailer with heavy fittings positioned far from the axle will be worse than the same trailer with those fittings positioned near the axle.
Some classic examples of undesirable horizontal weight distribution are:
- Compensating for wrong noseweight by positioning heavy items (lead-acid battery is a common example) at the far rear or the far front of the trailer.
- Using heavy materials for the pod structure.
- Lining the interior with heavy materials such as pine cladding.
- Fitting (and stocking) cupboards at the front, and at the rear, of the pod.
Vertical weight distribution
The noseweight of almost any trailer will reduce when the trailer is tilted backwards (nose lifted upwards) and will increase when the trailer is tilted forwards (nose lowered downwards). This is because any mass fixed on the trailer, if it is higher than the axle, moves rearwards as the nose is lifted and moves forwards as the nose is lowered. The higher the weight is positioned, the more exaggerated this movement.
So adding weight high-up on a trailer will exacerbate this, even to the point that a trailer may have a negative nose-weight when the rear is resting on the ground, yet have double the normal noseweight when the hitch is resting on the ground. This will make picking up the nose, and manoevering the trailer by hand, extremely uncomfortable and may cause injury as the down-force on the person lifting the nose varies wildly.
Weights high on the trailer – even if they are over the axle – will also exacerbate the ‘nodding’ problem because weight moved higher up the trailer is also moved further from the axle, just in a vertical direction rather than a horizontal one. And bad vertical weight distribution will worsen the nodding by even more than bad horizontal weight distribution, because of the effect it has on varying the noseweight as the car moves over bumps.
Such weights will also cause a large, temporary increase in noseweight when braking hard. In extreme cases, particularly if the tow vehicle is lightweight and has a long rear overhang, this phenomenon can unload the front wheels of the tow vehicle and reduce its ability to steer.
Finally, weights high on the trailer will reduce sideways stability, causing more weight to be thrown onto the outside wheel when cornering, potentially to the extent that a narrow trailer might overturn.
Poor vertical weight distribution can make towing a miserable experience. Some classic examples of undesirable vertical weight are:
- A spare wheel(s) bolted high on the side of the trailer.
- Roof rack.
- A roll-out awning.
- The additional structure required to strengthen the pod to accommodate a rear hatch.
- Kitchen fitments and food-stores on high shelves.
- Large-diameter wheels, which raise the whole trailer.
- An axle positioned unnecessarily far below the floor of the trailer, which again raises the whole trailer.
As with all other elements of good design, vertical weight distribution is about compromise. For example: if a feature – such as a roofrack – simply has to be included, then choose the lightest materials for it and its mounting-points, and consider even lowering the roofline of the trailer to help compensate.
Legs/Steadies and Chocks
Wind-down steadies are fittings designed primarily for the corners of caravans, to support the corners when pitched. They usually fit unobtrusively under the floor of the caravan.
Drop-down legs are fittings designed primarily for the rear corners of trailers, especially those with tailgate ramps, to take the weight of a load as it is moved up the ramp or lowered into the rear of the trailer. They generally fit on the outside rear corner of the trailer and remain permanently visible.
Either can be fitted to a teardrop, although finding any ready-made of appropriate size can be difficult: both tend to be manufactured at sizes which are too bulky and too heavy for very small trailers. And aesthetics is not one of their design criteria.
Alternatively, free-standing or detachable legs or steadies can be devised by adapting lifting jacks or axle-stands, or even made from scratch using telescoping lengths of tube. Some means to prevent detachment or folding of such a leg would be essential.
Most teardrops are likely to require one steady or leg, sited centrally at the rear. Two may be appropriate if the trailer is especially wide, especially lightweight, and has enough internal height to permit the occupant(s) to move themselves fully into a rear corner.
Any steady or leg would need to be fitted to a strong-point on the trailer. This should be planned in advance, before construction begins.
An alternative to legs and steadies may be to simply tether the nose of the trailer down to a strong-point in the ground, such as a ground anchor. This is only appropriate if it is virtually impossible for the occupants of the trailer to fully move into the rear of the trailer, and there is no other realistic way that excessive load will ever be placed on the rear of the trailer while it is pitched for camping.
When pitched for occupation, but not hitched to a vehicle, an unbraked trailer with a jockey-wheel has nothing to prevent it being moved by a slope or even by strong winds. If the trailer has steadies or legs, these may help to prevent it moving but would never be sufficient guarantee alone. The jockey-wheel (if any fitted) can be temporarily or permanently replaced by a leg fitted with a ground-spike – but even this is useful only on soft ground. So, in many circumstances, chocks or other means to prevent rotation of the main wheels will be required.
Insulation
Any useable pod requires insulation.
The primary purpose of insulation is to prevent condensation on the walls, roof, and floor. This comes as a surprise to most first-time builders. But without insulation a pod will be almost uninhabitable except in the most benign of conditions: condensation on the roof will drip on the occupants, condensation will run down the walls and contact bedding, and condensation will form on the floor making the mattress damp.
The secondary purpose of insulation is… to keep the interior cool. An overheated interior early in the morning, when the sun first comes up, is far worse than a cold interior: you can’t just add an extra duvet to keep the heat from cooking you out of the pod unreasonably early.
The fact that insulation will also help to keep the interior comfortably warm late into the evening is almost an accidental benefit.
Useful insulation requires three essential features:
- It is non-porous so prevents internal moisture-laden air from reaching the cold outer skin of the trailer.
- It forms a continuous and sealed layer over the whole of the interior walls and roof, and preferably also the floor.
- It conducts heat only poorly.
Some classic insulation fails are:
- Lining with fabric or carpet. This is virtually non-insulating. In any case it is porous so moisture-laden air seeps through the material, contacts the outer skin, where it deposits its moisture as condensation deep inside the material. The builder has swapped the visible problem of water for the invisible but insidious one of mould.
- Laying a polyurethane foam mattress onto the floor. Foam is porous so the heat from the occupant drives moisture-laden air downwards through the foam until the air reaches a point in the depth of the foam where it is cold enough for the moisture to condense. So the mattress gets wet from the inside.
- Internally lining with birch ply, or similar, to create a double-skin. Any failure to seal the entire perimeter of the lining allows the air-gap between the outer skin and the lining to exchange air with the interior. The result is copious condensation on the inside of the outer skin within the roof structure, causing water damage.
Bear in mind, too, that applying flexible insulation materials inside a completed pod will require the use of high-VOC glues such as contact-adhesive, resulting in considerable fume inhalation during (and possibly for some time after) installation.
Insulation should be planned early on in the construction. If it can be incorporated into the actual structure of the pod then it will be most effective and, likely, also lighter and cheaper than adding it afterwards. It will also be locked away inside the structure, safe from sources of ignition, removing the fire risk of having flammable materials exposed within the cabin.
There are two particularly excellent insulation methods, both of which incorporate the insulation as part of the structure:
- Double-skin construction. With a simple air-gap, or with added insulation.
- Foamboard construction. PMF over XPS for walls and flat roofs, home-made SIPs for floors.
Double-skinning is most appropriate for curved elements of the pod (curved roof, for example), while foamboard construction is better suited to construction of flat components.
Typically the floor of even double-skinned trailers is made from a single sheet of ply. This is strong, but has minimal insulation value. To prevent condensation on this type of floor, there are two realistic options:
- If the mattress is porous, cover the floor with a layer of closed-cell foam, such as used for budget sleeping-mats. This will prevent moist air contacting the floor and eliminate condensation.
- More simply, use a quality self-inflating mattress. These have multiple advantages. As well as not being porous, they are lightweight, easy to keep clean, and can be rolled up out of the way during the day.
Condensation cannot be completely prevented. So it is important – especially for any structure which includes wood – that the moisture always has a route to escape by evaporation. Interior ventilation, construction that doesn’t trap moisture, and a well-ventilated storage location for the trailer, are essential.
Internal Electrics
Before choosing electrics – 240V, 12V, solar – first decide what electrical devices you will be taking with you and how much electricity they will need. Then choose the lightest, simplest, lowest-cost and, above all, the most reliable system which will meet those needs. In almost all cases, this means nothing more than a cable connected back to the tow vehicle battery supplying a modest flow of 12V power to the pod. Or a small 12V power-pack for when the pod is pitched without the vehicle nearby.
Typical power consumptions
- Lighting: Modern 12V LED lights use very little power. A typical LED light marketed for caravans uses 0.25A on full power. To put that in perspective: a typical car 12V battery (if in good condition) will run that light continuously for a few hundred hours, before the battery goes flat.
- USB port: A typical 12V-to-USB converter, designed for fitting into vehicles, will use just 0.025A when nothing is plugged into it. A car battery can cope with that for thousands of hours before it goes flat, so in our designs we don’t even include an on/off switch. The same USB port, with a typical smartphone plugged in, will use about 0.6A while the phone is both charging and is in use. This reduces to about 0.15A once the phone has been charged. These are all exceedingly modest consumptions.
- Tablet computer: Powered from the same USB. TBS. We’ll measure and let you know.
- Laptop: Powered from a generic 12V converter such as those made by Kensington. TBS. Ditto.
- 12V TV: The TV’s specification (or a label on its case) will state the maximum consumption. Since a TV doesn’t have any significant output adjustments, this maximum is also likely to be close to the normal consumption.
Simple 12V systems
Sacrificing some amenity, to keep the system simple, has much to recommend it. Particularly reliability. The two simplest systems are:
- A 12V lead direct to the 12S or 13-pin tow socket on the towing vehicle. The main drawback with this is that, if allowed to, the pod occupants might continue to draw power until the car battery is too flat to start the vehicle. A voltage monitor (many 12V-to-USB converters incorporate one, with a voltage display) can help manage this risk. A monitor with an alarm or auto-cutoff can virtually eliminate it.
If the car battery is more than a couple of years old, have it professionally checked before using for this purpose: a failing lead-acid battery will often continue to start the car fine, yet has so little charge capacity that it will be run flat in a few hours of campsite use.
Some tow vehicles, such as camper-vans, will in any case have a separate leisure battery and this can be used to power the teardrop too.
Electric vehicles, of course, have a near-inexhaustible supply of power from their main battery and it is virtually unimaginable that a teardrop user would flatten an electric car battery in any realistic timescale. The power could even be enough to run a fridge and heater. - A 12V power-pack, re-charged from the vehicle while the vehicle is in use, typically daily or nearly daily. Many power-packs also provide USB power.
Some power-packs even offer 240V, although most are not especially efficient converters and in any case are only suitable for very low power devices. So, if those devices have 12V capability, it is usually more efficient to run them direct from battery anyway.
Solar
The headline price of solar panels is now so low, that solar appears to be a no-brainer. Before embarking on fitting solar to a teardrop, do beware the drawbacks and do consider the – far simpler – alternatives.
- In late autumn and early spring months – when power consumption is higher yet solar light is much reduced – the solar is unlikely to offer enough power unless a large system is installed.
- Solar will require a battery to store its power into. Until recently this meant a 12V lead-acid leisure battery. These are prohibitively heavy and any teardrop fitted with one is well on its way to becoming as awkward to use as a caravan. Modern systems can use lithium batteries but will require a more sophisticated battery management system and, unless they are LiFePo type, they are at significant risk of self-combustion especially if the management system malfunctions.
- Installed solar is fitted – rather by definition – to the roof. This means fasteners and cable runs. And therefore leaks. And, unless the trailer is a squaredrop with a roof higher than eye-line, unsightliness.
- Having a solar panel on the trailer means the trailer must be positioned in full sun – no option to pitch in the shelter of a tree, or a gazebo, nor even to use many types of awnings which might partially cover the panel. On some types of trailer, where the panel is inevitably on an angle, the location of the sun will also dictate the direction the trailer must be parked – which may well be at odds with the best direction to pitch based on slope or on site conventions.
- The solar panel won’t keep the battery charged over winter, if the trailer is kept under cover. Yet the battery will require top-up charging to keep it in good condition. Which adds to the winter maintenance schedule.
Alternatives to installed solar
- Free-standing solar with battery. These are panels with built-in batteries which can be placed on the ground near the trailer, supplying 12V to the trailer. Being free-standing, they can be located – and moved during the day – at the best angle to capture sunlight. Sounds perfect, except there is an even simpler alternative…
- Free standing solar, connected to the tow vehicle. These are panels fitted with integral circuitry designed for charging 12V car batteries. So the panel can be used to keep the car charged, while the trailer can be plugged directly into the car and use the car’s own battery to even out variations in solar input. Why carry a separate battery for the solar, when you’ve already brought one along in the tow-car?
240V and mains hookup
We’re not qualified to advise on 240V hookup design. There are safety – and legal – reasons that an electrician should be consulted whenever an outdoor 240V installation is carried out.
240V systems can be ‘simple’: essentially an external socket for connection to the supply, a power-breaker, and an internal socket. These allow the use of 240V devices inside the pod when on a campsite with 240V hook-up. Siting of the internal components – breaker and socket – are important considerations. They must be free from damp and condensation. They must also be protected from damage. And they must be sited so that they cannot be covered by fabric or bedding, most especially so that items like plug-in adapters cannot be smothered and will always have sufficient cooling air around them. Achieving all this, inside the tight space of a teardrop, will be challenging.
240V systems can be more complex, particularly by the addition of a ‘Zig’ unit which will use the 240V to simultaneously supply and/or charge the 12V system and may even allow the 12V system to provide a small amount of 240V – via an inverter – when hook-up is unavailable. This will require yet more units to be positioned safely within the teardrop. As at the very top of this section: before embarking on such complexity it is best to decide if the power requirements merit it.
Bear in mind that 240V hookup is charged extra at most campsites. And hookup is often only available on the more expensive pitches, so it increases the cost of a night’s stay twice-over.
User’s reasons for fitting 240V hookup, with alternatives
- To charge a toothbrush. Braun offer an inexpensive toothbrush powered by AA batteries. Fitted with Energizer Lithium AA’s, this will run for a month or more of twice-a-day usage. And no need to carry a charger on holiday.
- To charge a phone, tablet, laptop. Converters to power these from USB or from 12V are widely available.
- To power a TV. 12V televisions, designed for caravans, are widely available.
- To power a coolbox or fridge. Certainly, most coolboxes are too power-hungry to run from 12V without the car engine running. Alternatives are to use an unpowered coolbox and buy ice for it every other day, or to use a coolbox with a gas option.
- To power a heater. 12V could never supply enough power. But the primary question here is of safety. Can a heater be used in such a small space that’s likely packed with flammables?
- To power an electric blanket. If this is an essential, and hot water bottles won’t suffice instead, then really there’s no alternative to 240V.
Circuit Protection
Protection, such as fuses and RCDs, are required for all circuits, including 12V ones. Every wire should be fed via at least one fuse which has a rating lower than the wire itself – preferably significantly lower.
Any fuse must be chosen so that it is guaranteed to blow in event of a short-circuit, after taking account of the resistance of the circuit and the fuse factor. This applies to 12V cables and 240V cables alike. If in doubt, consult an electrician who can calculate this for you.
Solar panels require protection against reverse current, such as might occur at night while the panel is making no charge but is still connected to a battery. Most rigid panels have this built-in but check before connecting, especially flexible panels.
Batteries require a battery management system (BMS) to prevent over-charge or over-discharge.
Earthing of mobile and portable mains equipment – including inverters – is a complex subject. In some cases installing an earth is essential and in other cases it can be dangerous. Seek advice from an electrician.
Routing
Cables are unsightly and vulnerable to damage if exposed. In many cases the builder will wish to run them either in trunking or concealed within the structure – such as within a double-skin. Cables routed in enclosed spaces or routed against insulation must be downrated to prevent overheating. Cables routed within the structure – where future repair may be impossible – should be tested prior to closing the structure.
Electrical Losses
Most auto-electrical retailers offer cable in various gauges, and usually quote a maximum current that the cable can handle. However, a cable used near its maximum rated current will cause a significant voltage drop along its length. These losses, combined with the risk of overheating, mean that it is generally best to substantially oversize any cabling.
A good supplier will quote the resistance of any wire (in ohms per metre). This can be used to calculate the voltage drop in a length of cable under load.
Audio Equipment
While it is tempting to install a car audio head unit into a teardrop, there are good reasons not to:
- Car head units almost invariably require a permanent 12V supply to maintain their settings and memory. If the trailer has a battery, this will be a constant drain on it. If the trailer has no battery, then the unit will reset to factory defaults every time power is disconnected.
- Separate speakers are required.
- Car equipment is not designed to minimise power consumption, there being a plentiful supply of power in a (moving) car.
- Car audio has high power outputs – many tens of watts per speaker – to overcome ambient noise. This is far, far louder than required in the quiet interior of a teardrop.
If a 12V TV has been installed, then many of these will also receive DAB and possibly also FM and AM. Some will also accept a bluetooth connection from smartphones.
In the absence of a TV, ordinary portable audio equipment will work well. FM broadcasts, online channels, podcasts, and music can be bluetooth’d from a smartphone to a portable speaker – which itself can be recharged from a USB port. FM, AM, and DAB can be received on a portable radio.
A Note on Battery Types
There are four types of rechargeable battery in common use for consumer devices:
- Lead-Acid. Until recently, these were almost universally used for vehicle and vehicle-leisure purposes. Their advantages are that they are cheap, require only the simplest charging systems, recharge reasonably quickly, and aren’t easily provoked to self-combust. On the other hand they are phenomenally heavy, and require frequent topping-up of charge to prevent degradation due to self-discharge.
- Ni-MH. (Nickel metal-hydride.) Rarely used for vehicle-leisure purposes. They are generally safe to use, require only a slightly more complex charging system than lead-acid, and are somewhat lighter. On the other hand they are expensive, have only modest capacities, and can be recharged only slowly.
- LiPo. (Lithium polymer.) These are now commonplace in almost every application where rechargeables are required. They are super-light, have high capacities, are inexpensive, and can be recharged extremely quickly. On the other hand they require a very complex charging and monitoring system. They must never be over-charged and they must never be fully discharged: in either case they would then be likely to catch fire, either immediately or during subsequent use. If they do combust, they burn extremely fiercely. These are the same battery type made notorious by deadly e-bike fires.
- LiFePo or LFP. (Lithium ferrophosphate.) A variation on Lithium battery chemistry which is considerably safer, in particular far less likely to combust. Storage capacity is somewhat less than for LiPo. Increasingly, LiFePo batteries are available in ‘car’ battery format and as ‘power packs’, with the package containing both the cells themselves and a battery management system which oversees charging and discharging without any need for a complex external charger or discharge monitor. Of the four types of battery listed here, LiFePo’s generally have the longest life expectancy in terms of number of charge/discharge cycles.
For balance of safety (if you can even ‘balance’ safety against other factors) durability, re-charge rate, weight, cost, and convenience – a LiFePo pack with built-in battery management system (‘BMS’) is probably top of the list. Even then, we would be wary of building such a battery pack into the teardrop itself, preferring to park it at the end of an extension lead away from the accommodation or, at the very least, installing it behind a firewall and in a fireproof charging bag.
Beware cheap ‘power packs’ which use LiPo batteries to cram in more capacity: your safety depends utterly on the electronics in the pack. If those electronics fail, allowing the battery to be over-charged or over-discharged, the LiPo in the pack is highly likely to catch fire during future use. Or even spontaneously when not in use.
Safety
Finally, if fitting any electrics to a teardrop there are some essential safety considerations:
- Shock: 240V is dangerous. Occupants must be protected both by separation from the wiring and by modern wiring protections such as RCD. Do not wing it: have an electrician design the installation.
- Ignition: any electrical wiring, whether mains, battery, or solar, is an ignition risk if damaged or wrongly specified. Correct fuses provide some protection against this, but good design, high-quality components, and careful installation are essential preventative measures.
- Fire: lithium batteries, including solar storage and ‘power packs’, are themselves prone to self-igniting (and will burn extremely fiercely) especially during charging. Low quality solar panels themselves can also self-ignite, particularly any built-in diodes and controllers. Devices such as heaters and hairdryers are a fire risk if used near bedding – which in most teardrops means anywhere inside the entire of the pod.
Construction Methods and Materials
Home-built teardrops can use many materials. The list is endless. Here are just some, with pros and cons.
When commenting on a construction’s weather resistance, we’re assuming that the trailer is stored outdoors year-round under a breathable fabric cover in a reasonably airy location. Depending on where and how your own trailer is stored, your material and construction choices may vary. Storage in a dry, low-humidity building would allow a more delicate or corrosion-prone construction. Storage outdoors without a cover would require an even more weather-resistant construction.
Thin Aluminium Sheet
Thin sheet aluminium – typically 0.9mm – is readily available and easily shaped. Frequently used as a cladding material, either over an open frame (steel, timber, aluminium) or over a closed shell (plywood).
Ally is probably the first material which comes to mind for exterior roof and walls, when a teardrop is mentioned. Its appearance is timeless, it doesn’t require expensive and maintenance-heavy painting, and it is intrinsically waterproof. So, on the face of it, aluminium cladding is almost a no-brainer. The reality is more nuanced.
Aluminium cladding joints
Joints where the edges of two aluminium-clad components meet are extremely difficult to make well. For example, where the curved roof meets the flat wall. Particular issues are aesthetics, sharp edges, and leaks. Unless they have exceptional welding skills, there are only two leak-proof construction methods available to the home-builder:
- Lap-joint with a continuous bead of adhesive, and no fastener holes.
- A porous joint, engineered by folding, so that water will always fall out of it towards the outside.
Neither is particularly easy to achieve while retaining good aesthetics and avoiding exposed sharp edges. So a tempting ‘solution’ is to make the joint and then hide it under a beading or cover strip, usually also of aluminium but sometimes other materials. Still hardly beautiful. But, worse, if this is fitted using fasteners (even plus mastic) the aluminium cladding will still move and work the holes bigger (see below) creating more water leaks. It is not realistic to glue such a cover strip in place without fasteners: the small bond area would inevitably allow it to peel away, becoming a spear ready to kill the next pedestrian or cyclist you overtake.
Joints where the edge of aluminium meets another material are equally problematic. These will occur at doors and other openings, and where the roof/wall meets the floor. Even allowing that the aluminium can be dressed inwards around the opening, or under the floor, there will be points where this is not possible: at sharp corners for example. It is at these points that water will penetrate, so it is essential to have a design carefully drawn to omit any such points: because even if 99% of the trailer is watertight, the 1% that leaks will cause water-damage.
Joints where aluminium must overlap, perhaps because the builder does not have access to material larger than the commonplace 2500mm x 1250mm sheets, can be made by bonding with a flexible adhesive such as Soudal Fix-All Hi-Tack. The joint should have a large overlap, allowing sufficient bonded area to overcome the tension which will be created when the aluminium shrinks in cold weather. If the joint is on a curved surface, the joint should be made when the aluminium is formed around that curve: the double-thickness of aluminium will not later form around the curve easily, if it has been bonded when flat.
Aluminium as cladding, for waterproofing.
Often, a plywood teardrop is clad in non-structural aluminium to waterproof it and/or as decoration. Leaving aside the increase in weight this incurs, and the difficulty of making joints (see above) it will almost certainly fail in its objective of protecting the structure:
- Any fastener holes (screws, rivets) will leak. Doesn’t matter how much sealant or mastic is used. The aluminium will expand and contract with day/night temperature cycles and from vibrations during towing. It will quickly stretch those holes, allowing water in. Once the water is in, it is trapped in the very structure that the aluminium is supposed to be protecting.
- When the interior is heated, by occupancy or by sunlight, any moisture vapour inside will migrate outwards through the porous part of the structure (the plywood) until it meets the non-porous part (the aluminium cladding). If the aluminium layer is cool enough, the vapour will condense there and soak back into the timber. The end result is that the timber stays wet permanently.
Any such cladding therefore needs to be absolutely and totally watertight and, even then, the pod will require excellent ventilation and careful storage in an airy location to prevent moisture affecting the structure from the inside.
Cutting aluminium sheet
Ally sheet should be cut with a nibbler, not with snips. A nibbler will not deform the edges of the material. Snips will leave a wobbly and bent edge. Keep some degreaser handy: nibblers cut better if a little oil is used, and this will need to be removed from the material before it can be glued.
Low-cost nibbler attachments for portable electric drills are widely available.
Vision vs detail
The enticing vision of broad sweeps of metal covering the roof and the walls should not let you forget that, with aluminium, the devil is very, very much in the details. So, before embarking on an all-ally pod, or an ally-clad plywood pod, first decide how all the joints – roof, walls, doors, vents, floor, exterior lights, and even the small external fittings such as hooks for awnings – will be jointed, be made absolutely watertight, be made safe from exposed sharp edges, and yet still be presented elegantly.
Aluminium Composite Sheet
In recent years this once high-tech product has reached the mass market, and is now surprisingly affordable. In cost it is nearly on par to Lloyds marine plywood (allowing for the cost of varnishing that plywood).
On paper, it is a fabulous material: self-coloured, rigid, strong, waterproof. However, it suffers one key disadvantage: any cut edge must be covered or trimmed to conceal the resulting two aluminium edges which – each being only 0.3mm thick – are extremely sharp.
This material can potentially be used to make a stunning teardrop. However, the devil is even more in the detail that with plain sheet aluminium, and exceptional design skills will be required to overcome the issue of exposed edges on anything but the simplest of shapes.
Self-builders commonly use this to clad squaredrops, where right-angle trim at all the edges can easily be used to cover the joints neatly.
Aluminium Tread-Plate
This may be used to make steps and mudguards on a teardrop, most commonly on a squaredrop where it is more aesthetically appropriate than on a classic-teardrop.
It is not an easy material to use, being quite heavy gauge and having a strong embossed pattern. The gauge makes it difficult to bend accurately. The pattern will look ‘wrong’ if two pieces meet at different orientations.
There are, generally, better solutions to most problems on a teardrop than tread-plate. Very much a last resort, unless used as an aesthetic choice to create a particular ‘look’.
Sheet PVC or uPVC
This is plain solid sheet PVC, generally 1.5mm thick. Not to be confused with the extruded uPVC profiles widely used for residential windows, doors, and soffits.
An economic, flexible, versatile, and easily-worked material which, after preparation with a surface activator, can be strongly and reliably bonded using Soudal Fix-All onto substrates such as timber.
Typically available in 2440mm x 1220mm sheets.
PVC is – of course – entirely moisture-proof. It is far from rigid so requires a structural backing of timber or other framing.
If used on a curve, rather than flat, sheet PVC will keep its form considerably better. Useful, therefore, as an inner liner for the curved roof of a classic-teardrop, for example. But less useful as the inner liner of a flat wall, where – being flat without a curve to help it retain its form – it would tend to flex noticeably between the framing elements.
Can be brittle under impact, or if folded sharply. Especially in cold conditions.
Very much not recommended for external use, neither for cladding the walls nor for the outer element of a curved roof, as it will quickly lose its shape when exposed to the heat of sunshine, even if fitted on a curve.
Foam PVC board
Foam PVC boards are available self-coloured in bold colours 3mm or 5mm thick. Supplied in sheets up to at least 3050mm x 1560mm. Also available in greater thicknesses, but the prices become prohibitive. Designed for indoor use and what the makers describe as ‘seasonal outdoor use’. Common trade names are Palight, Ex-Cel, and Forex.
The material’s characteristics are quite different to the solid uPVC sheets. Foam PVC is a moderately rigid but slightly springy material, with characteristics somewhat like a sheet of thin plywood.
We’ve never used it on a project as large as a teardrop, but it does appear potentially suitable for internal, and possibly external, cladding. We find it can be bonded to a surface reasonably well with Soudal Fix-All Hi-Tack, but lists of approved adhesives – which include some with similar characteristics to Fix-All – are available from sheet suppliers.
Unlike aluminium composite sheet, any cut edges wouldn’t need covering for safety and neatness. So this is certainly a material worth investigating as a potential cladding, but would need testing outdoors to be sure that it won’t have the drawbacks of uPVC sheet when used over a large area and heated / cooled by the weather.
Steel
Most teardrops will have a steel chassis. A few, though, go further and have the pod frame built from steel.
Typically, such a pod frame will be built from box section mild steel. To save weight the structure can be a composite of steel with some softwood framing elements, although light gauge steel box is available which may be no heavier than timber anyway.
If building a curved shape then forming the roof members will be difficult in a home workshop. Smoothly curving hollow steel section is no easy task, no matter how light a gauge it is. The best that can realistically be achieved is to partially cut at intervals, allowing the length to be bent to a series of straight lines which approximate the curve. Even then, rewelding at the cuts to restore the section’s strength would cause the bends to tighten as the welds cool, giving unpredictable results.
The eventual fitting-out can be made much easier by incorporating ready-made headers and sills for vents, doors, windows, etc, and having ready-made strong-points or brackets for shelves, seats, interior lights, TV, support legs, mudguards, external lights, etc, and by having enough studs and noggins to sufficiently support the cladding. All of these can be welded onto the chassis/pod before cladding and fitting-out are begun. This does, however, require careful design and planning because there are limited opportunities to make corrections once cladding has been completed.
Steel framing the pod appears to lend itself well to double-wall construction by cladding both the inside and outside of the frame, possibly with insulation between. However, if both inner and outer cladding are directly fastened to the steel frame, the entire length of every frame element will make a ‘cold bridge’ from outside to inside: severe condensation will form on the inner wall wherever it touches the frame. This can be overcome either by forming the wall structure using vertical studs then fitting horizontal battens (possibly of some other, lighter, possibly less thermally conducting material) on the inside of the studs to carry the inner cladding, or by using stand-offs to carry the inner (or possibly the outer) cladding.
At the design stage, bear in mind that a single frame element fitted along the edge of the roofline cannot carry both a double-layer wall and a double-layer roof. Additional battening will be required for one or the other.
Also bear in mind that building the pod frame and the chassis as a single welded unit may require deciding on the axle location early in the build. Yet at that stage it will be almost impossible to calculate where the axle should be positioned to obtain the correct noseweight. The completed trailer, therefore, may end up having a noseweight so high, or so low, that it is unuseable, unless installing the axle fittings is left until after the rest of the trailer is complete and fitted-out.
Corrosion
Corrosion can be an issue. If the external cladding is riveted to the frame then water penetration at the fasteners is likely to cause rapid corrosion. Conversely if the external cladding is glued to the frame then even minimal future corrosion of the frame – which is almost inevitable no matter how well painted – will de-bond the adhesive.
Galvanising the frame might be an option, but there are serious drawbacks: difficulty of transporting and cost of galving such a large item, risk of warping while being dipped, and the inability to make further (welded) alterations after galv has been applied. So-called ‘cold galvanising’, using a zinc-rich paint, is little more effective than any other paint.
Powder-coating is possible. It has an unjustified bad reputation, and a sand-blast followed immediately by quality powder-coat primer followed by a powder top-coat will last for years, even fully exposed to the weather. But finding a powder-coater with a large enough oven to fit an entire trailer – chassis, pod, and all – may be challenging. Worse, few glues will bond successfully to powder-coat, and drilling for fasteners will simply re-expose the steel.
Aluminium, in particular, when clad onto steel will suffer corrosion unless absolutely watertight against rain and also proof against any risk of condensation inside the double-skin. Aluminium and steel in contact, in combination with damp, will cause galvanic corrosion which can rapidly eat away the aluminium – including any aluminium fasteners such as pop rivets. Road salt will worsen this many-fold. Double-sided adhesive foam tape can help isolate the metals, but will not be sufficient to hold the panels without fasteners.
Galvanic corrosion might be largely overcome by using aluminium battens to hold the external cladding, themselves carefully fastened to the steel frame with sufficient corrosion protection. Possibly even timber battens, but then damp retention becomes a risk. Such battens would also usefully increase the thickness of the double-wall, allowing more insulation. But, either way, the complexity – and weight – of the build will increase greatly.
However a steel frame is clad, all steel elements should have drain holes at the very bottom, clear to the outside/underneath of the trailer, so that any water or condensation inside can always escape. Although hollow steel cannot be painted inside, it is little trouble to coat the insides of all tubes with an anti-corrosive such as Bilt Hamber S50 which can be applied – using a flexible lance – through the drain holes.
The key to a successful steel-framed build is likely to be extremely careful planning. And, of course, the ability to weld to a high standard.
Commercial
Occasionally, commercial ready-built chassis-plus-pod steel frames appear for sale on auction sites but, although these are visibly teardrop-shaped-objects, they may need a lot of additions before they are ready to be clad and fitted-out. Such pods should be examined closely with a designer’s eye. If fittings still need to be added (by welding) anyway, then building your entire own steel pod from scratch may be more satisfactory.
Aluminium Framing
An aluminium-framed pod, using hollow extrusions, would have similar characteristics to a steel-framed one, except it would be much lighter and much less corrosion-prone.
The pod could be perhaps be partially built from aluminium construction. For example a lightweight wall could feasibly be constructed using channel top and bottom, with vertical lengths of channel or square tube to make studs. The construction then clad both sides to form a rigid whole. Much in the manner of a metal-framed stud-and-track partition wall often used in residential and commercial buildings. Rigid jointing of the aluminium frame would not be required, because the cladding itself would provide this.
But jointing aluminium extrusions to make a complete teardrop frame, by any method other than welding, would probably be both time-consuming and overly complex. If you can weld aluminium – a rare skill – then an aluminium frame might have much to recommend it.
Timber
Timber has a bad rep in the teardrop world. This is largely because of the use of inappropriate plywoods and poor early designs – typically thick and heavy sheets of non-waterproof plywood being joined together to make some type of box, inadequately waterproofed often with poor-fitting aluminium cladding. These early trailers were massively too heavy, had limited ventilation, and suffered endlessly from condensation and ingress of rain. Many simply fell apart due to delamination.
But all spheres of engineering have their early failures, lessons are learned, and designs are improved to prevent further such failures.
There are some tremendous advantages for the home builder in using timber, which should not be overlooked:
- Timber is light, stiff, inexpensive, and readily available.
- Timber is easy to work with only simple tools.
- Timber elements can be jointed with great ease, using nothing more than inexpensive adhesive and a few clamps to create almost invisible joins.
- Where cut edges of sheets are exposed, they don’t create the immediate hazard of a sharp edge requiring the complexity – and inelegance – of trims, capping-strips, or dressing-over. Even if a cut sheet edge is judged excessively thin, the thickness can simply be doubled-up by gluing on further layers.
- An error during the build can often be entirely and almost invisibly rectified by cutting-out a part and replacing it, or scarfing-in some additional timber. This is especially useful for the builder of a one-off, who does not have the luxury of working through multiple iterations of prototypes, binning each and starting again repeatedly.
- Varnished timber has considerable beauty.
There are two types of timber commonly used structurally on a teardrop and readily available from timber merchants and builders merchants:
- PSE (or the slightly less useful PAR) planed softwood, generally untreated.
- Plywood.
PSE is ‘planed square edge’. So the wood is planed on four sides so that adjacent sides are at right-angles. A very useful feature when it comes to constructing frames, and when jointing plywood to make, say, cubbyholes. Even more useful is fillet (triangular section) timber, usually available in a range of sizes.
PAR is ‘planed all round’. There is no guarantee that the sides are at right-angles.
Both are generally ‘redwood’, which is denser, harder, and better quality than the cheaper ‘whitewood’.
PSE and PAR are – usually – sold by timber and builders merchants measured by their pre-planed size. Allow 3-5mm smaller, in their as-supplied size. In DIY stores, the sizes stated are more likely to be actual. Timber and builders merchants will quote PSE and PAR prices per metre length, excluding VAT. It will be half the price, or less, from a builders merchant compared to a DIY store. And probably even cheaper at a timber merchant… providing they will even deal with you. Most merchants will allow you to select your own lengths from racks full of usually random lengths of timber, so take your time and choose knot-free, straight examples. They’ll also usually be happy to lend you a handsaw to cut it up to fit in the car. Take a tape measure.
Plywood comes in standard thicknesses. Leaving aside specialist plies, thicknesses available are generally: 3mm or 4mm (both somewhat uncommon), 6mm, 9mm, 12mm, 15mm (uncommon, possibly obtainable by special order), 18mm, and 25mm.
Plywood sheet sizes are generally 2440mm x 1220mm (8′ x 4′) and ‘a sheet’ invariably means a sheet this size. Some rare variants may be 2.5m x 1220mm. And a few of the more commonly used types can be obtained in 10′ x 5′ sheets but generally only by special order – and a special order of less than at least half-a-dozen sheets will usually attract a large and uneconomic premium. Lifting a (8×4) sheet of 25mm will require two people, and even 18mm is a struggle for one. Sheets can be joined: see adhesives, below.
There are many variations of plywood. They are rated by the type of glue used and the surface finish. Some of the more commonly available types (in ascending order of waterproofness) are:
- Interior ply. Not so widely available now, although some lightweight ply boards (commonly poplar – used for camper van furniture to save weight – and birch) may be interior grade. Interior ply will rapidly delaminate in the presence of any damp, even if painted.
- Bending ply. Interesting stuff. Two layers of ~3mm timber laid with their grains parallel, bonded either side of a thin flexible substrate. The result is a plywood which can be rolled up like a carpet. Comes in two directions of grain: ‘barrel’ meaning the grain is across the short length of the sheet so it can be rolled up to make a short stubby barrel shape; and ‘column’ meaning the grain is along the long length of the sheet so it can be rolled up to make a tall thin column. Unfortunately, all bending ply is made with interior grade adhesive.
- Birch ply. This may be made with cheap timber faced by birch, or may be birch right through. A wide range of thicknesses are available, including very thin – down to 0.8mm – variants. Beware that it may be made with any kind of adhesive and it will be hard to pin down reliably whether that adhesive is truly waterproof but, in general, birch ply will be intended only for interior use. Quality birch ply can be extremely beautiful. Thicker boards can be machined in 3D to reveal different depths of plies.
- Exterior ply, aka ‘builder’s ply’, ‘WBP’, ‘red-and-white’, ‘far-eastern’, ‘exterior grade’, ‘weatherproof’, also occasionally called ‘Q-marked’ and even ‘good-one-side’. These are variants of the most common ply available in the UK. All timber merchants and all builders merchants stock it. WBP is an old name, but still widely used to identify this type of ply.
- Builder’s marine ply. Superficially, this looks like exterior ply, apart from the fuzzy blue ‘marine’ text stamp in one corner and/or along the edges. Previously considered quite exotic, now many merchants stock it as part of their standard range.
- Lloyds-approved marine ply. The ultimate in marine plywoods, certified by Lloyds for use on marine vessels and, as a bonus, almost always having a beautiful grain visible both sides. Available only from a select few suppliers. If you happen to live in Bristol, head to Robbins Timber and compare this stuff to the much cheaper builder’s marine.
Of all these types of ply, only two are likely to be affordable and of use to home-builders:
- Exterior ply. The old name, WBP, stands for Weather and Boil Proof – a trades-description-busting moniker if ever there was one. The name was discontinued in 1995 but, the building trade being what it is, still widely recognised. Exterior ply can be used sparingly for interiors, but only if the interior is guaranteed to be moisture-free except for brief periods of light damp. Absolutely do not use it for the floor or on the exterior, not even if the exterior is to be clad in aluminium, PMF, or any other weatherproofing. Do not use it for framing inside twin-wall construction. This type of ply will delaminate in the long-term presence of moisture or high humidity, whether painted or not. Beware, also, that this ply usually has only a paper-thin decorative laminate on both sides. Even a light sanding will go through it, ruining the surface appearance. Sometimes different grades of exterior ply are available, based on number and size of defects in the laminates. Anything further up the alphabet than ‘B/BB’ shouldn’t even be considered.
- Builder’s marine. This has massive advantages over exterior ply. Firstly, the glue is waterproof. Permanently waterproof. You can use this stuff, even completely unpainted, underwater (we have) and it will barely delaminate, even after years. Secondly, the surface laminates are much thicker, so can be sanded quite extensively. The thickness of the surface laminate also allows paints and varnishes to soak in deeper, before they are blocked by the adhesive layer.
Until recently, the glue used in plywood was the main cost factor, with marine ply costing several times the price of exterior ply. (And yet some people were still prepared to pay that extreme premium: which should tell you something about how good it is.) Now, with the recent rapid rise of raw timber prices, this has changed so that marine is now less than twice the price of exterior ply. Which still sounds a high premium to pay… but compared to the hundreds of hours of labour you’ll put into designing, cutting, shaping, and finishing it’s a very cheap price to pay to have your trailer hang together for longer than a couple of years. So pay the extra, always order marine ply, and send it straight back if you can’t see the word ‘marine’ stamped on it.
Don’t let the merchants tell you that exterior ply is waterproof: it isn’t and there are dozens of sad stories on teardrop forums to prove it. The only possible use for it, in any teardrop which will be stored outdoors in the UK, is of the 6mm type which can feasibly be used for interior shelves, cubbyholes, and interior linings. We sometimes choose 6mm exterior for these very dry applications because it will usually be of better construction and visually more attractive than 6mm builder’s marine.
So the single most important piece of advice, if you take just one thing from this page, is: don’t use exterior ply for the structure or exterior of a timber pod, irrespective of what you plan to coat or clad it with. The only plywood for use externally on a pod is marine plywood.
Other sheet timber products
A number of other products are available:
- Hardboard. Heavy. Weak. Not even slightly water resistant. About as useful as cardboard.
- MDF. A much maligned material but in reality extremely useful… in the right applications. Essentially wood dust bonded with adhesive. Cheaper (much cheaper) than ply, and with a much finer surface, but heavier and weaker. Available in standard and ‘water resistant’ (aka ‘green MDF’), neither of which will survive long-term moisture. Difficult to justify the weight on a teardrop, even ignoring its vulnerability to water. Working with MDF comes with health risks: the dust is unsafe to inhale even in small amounts.
- Chipboard. Essentially, a coarse version of MDF. Again, heavier and weaker than ply. Again, not waterproof.
- Furniture board. Chipboard or MDF, coated in a thin layer of PVC. Typically used for construction of kitchen units, wardrobes, and similar. Heavy and weak. All the drawbacks of the base material are revealed, when any water seeps into the cut edges.
- OSB. (Oriented Strand Board) aka ‘Sterling board’. Little more than a much coarser version of chipboard. With all the same drawbacks.
- Shuttering ply. A very coarse, cheap ply mostly used to cover openings in a part-finished building. Water resistant up to a point, but will delaminate with long term exposure.
- Wall panel. These are panels, typically of water resistant MDF, coated in a heavy impervious and decorative layer of melamine or PVC. Sold for use to line shower cubicles and wetrooms. We have no experience of these in any long-term damp application. But their sheer weight would be sufficient to put us off using for a teardrop.
Paint and Varnish for Wood
The most important assumption made about paints and varnishes on wood is that they waterproof the wood. Except… they really don’t. They will massively reduce liquid water penetration into timber but there are none which seal out moisture entirely. Even when newly applied they are almost all somewhat permeable to water vapour. In any case, after a few months of day/night temperature cycles, movement of the timber, and some sunshine UV, they will all crack, leaving openings for actual liquid water to penetrate. After that, coating failure and timber discolouration are just a matter of time.
So the key questions when it comes to coatings are: which ones will adhere for the longest, and which will preserve the appearance of the timber for the longest?
- Bonda G4 High Gloss clear. Starting with our favourite – by far – for interior and exterior use on plywood. This stuff is nearly perfect. It soaks deep into the timber, bonding permanently. Sets very hard in a few hours, allowing the surface to be sanded to a very fine finish ready for recoat to create a gloss finish that brings out the woodgrain. Multiple coats can be applied only hours apart, so the job gets done quickly with minimal dust/insect inclusions. Can be applied by roller or brush, and never shows an ‘edge’ while being applied. It is reasonably UV-proof so, provided the trailer is stored generally out of direct sunlight, it can be used on exterior plywood. Four coats is enough externally, and two internally. And – one of its best features – it is compatible with Soudal Fix-All so parts can be pre-varnished and then glued together afterwards. The main drawback is that old G4 is difficult to prepare for future re-coating: so if it ever does fail (and we’ve never seen that happen) it may be necessary to strip back to bare wood to recoat. The other drawback is strong fumes during application, requiring extensive ventilation or PPE. First coat should be applied extremely generously, so that the timber is given opportunity to soak up as much G4 as it can absorb. Further coats must be applied sparingly to avoid runs. On large areas, best applied with the substrate laid horizontal.
- Bonda G4 Pond clear. Also Kovertek G40. These are specified for sealing concrete ponds to minimise lime from the cement leaching into the water, and for sealing bare concrete floors. They can be applied to timber just as well as G4 High Gloss, with almost identical results. Considerably cheaper. However, they are not UV proof so should not be used externally. Also widely available in blue.
- Yacht varnish. All types, including polyurethane, including those from genuine marine-oriented manufacturers. Not advised. Has little penetration into any type of wood or plywood. Difficult to get a good finish on large areas. Prone to rapid cracking. Prone to UV damage. Prone to water creeping underneath and lifting away. If left exposed to weather, requires frequent scrapping-back and reapplication.
- Acrylic varnish. Not waterproof.
- Clear epoxy (used as a varnish). Not advised. Not designed for the purpose. Little better than yacht varnish for penetration. More difficult to apply on large areas than yacht varnish. Extremely prone to UV damage. Easily cracks with movement of the timber. Difficult to recoat (does not bond well to itself). Difficult to overcoat with other materials (forms a waxy deposit on its surface during initial cure, which is difficult to remove.) Almost all brands are extremely smelly during application although this rapidly fades, one exception being West Systems which we find considerably more bearable.
- Clear polyester resin (used as a varnish). Not advised. Not designed for the purpose. Bonds poorly to timber, plus many of the disadvantages of epoxy. Smells awful and continues to smell for years after application.
- Yacht paints from genuine marine-oriented manufacturers such as International. If applied by the book, with the necessary preparation, primer, undercoat, and overcoat, are likely to be considerably longer-lasting than any clear coats except, perhaps, G4.
- Yacht paints from generalist manufacturers of paints. Not worth the risk. Use something genuine.
- Household paints, glosses, water-based exterior paints, one-shot ‘no-primer-needed’ paints. Not worth the risk. Use something genuinely manufactured for marine use. Except…
- Zinsser BullsEye 1-2-3. Excellent for priming difficult surfaces and overcoating difficult coatings. May be useful when restoring a second-hand teardrop or chassis.
- Bitumen-type paints, underseals, etc. Not advised, not even for waterproofing a tired old teardrop for ‘just another year’. Even if they do bond successfully to the substrate they will crack and then – being non-breathable – will seal in any water which gets under them. Some will melt or become sticky in hot conditions.
- Osmo Hardwax (exterior UV-proof grade). Astonishing stuff… on solid hardwoods such as ash and oak. But poor performance on softwoods, outdoors. Untested by us on plywoods but unlikely to successfully seal any exposed end-plies.
- Danish Oil. Widely used on kitchen worktops. Not for its performance but because it is food-safe. Performance even indoors is poor. Outdoors likely to be very poor.
2-Pack Spray Coatings
Although these have superb performance, we’ve excluded them from the list. The PPE and safety procedures necessary to avoid serious health risks are beyond most home-builders.
Composite Coatings for Wood
A composite coating is created by applying a layer of material – glass mat, canvas, cotton, muslin – onto timber and bonding it to the timber by stippling or rollering a liquid – resin, PVA, varnish – through the material so that, when it dries or sets, it bonds the material to the timber.
There are a few circumstances where a teardrop builder – or especially a refurbisher – might apply a composite coating, but results are likely to be disappointing. Applying over the entire outside of a plywood pod which is at risk of – or is already – delaminating is the most common motivation for using a composite coating. The assumption – or hope – is that the extra thickness and integrity of a composite coating will out-perform paint and keep the structure dry, preventing (further) deterioration.
The problem is that, in any porous or partially porous structure, moisture vapour always moves away from heat towards cold. So moisture inside a warm pod will migrate outwards through the porous part of the structure (the timber) until it meets the non-porous part (the composite coating). If the composite layer is cool enough, the vapour will condense there and soak into the timber. The result is that the structure becomes wet – and stays wet.
In general, a composite coating will, indeed, keep external liquid water out of the structure for longer than paint. However, the coating is not only waterproof, it doesn’t let the timber breathe at all. The end effect is just the same as with an aluminium-clad timber pod: there will inevitably be small gaps in places, water will get in, be trapped between timber and coating, and the water will be unable to evaporate outwards. The air in the interior of the pod will rapidly reach saturation so the timber spends more time wet than it does dry, and the delamination continues.
A second motivation for using a composite coating, and especially for using GRP, is to enhance the stability of joints where, say, roof and wall meet. In such case, it would be worth considering instead just epoxying glass tape along those joints, rather than coating the entire of all the panels. Keep in mind that glass tape does not form well around outside corners unless the edge is heavily radiused.
For those not put off by the risks of a composite coating, here are some options:
- Glass mat and polyester resin. Widely used for boatbuilding, so seems an obvious choice. But there are downsides. Polyester doesn’t stick to wood very well longterm or in presence of water. It smells awful, both during use and long after it has cured. Glass mat is heavy and does not form easily around outside corners.
- Glass mat and epoxy. A better choice, in that epoxy adheres well to wood and has far less smell after it has cured. It will require painting because UV degrades it. The finish will be rough due to the nature of glass mat, although glass tissue (a very light version of mat) might be used instead to give a finer finish.
- PMF (see below).
- G4 (‘Pond’ variant – for economy and also because it is more viscous) soaked into cotton muslin. We’ve had interesting results with this. Certainly it bonds extremely well, stays bonded for a long time and, in our specific test, did not crack. The muslin soaks up far more G4 than the timber alone ever could, creating a very thick layer. In our tests it kept some questionable-quality ply in reasonable condition for three years of continuous exposure, after which we painted it (grey Zinsser Bullseye 1-2-3) due to visible UV damage to the coating. However, the coating was applied only to the curved roof of the pod, not the whole pod, and the roof structure was already protected against vapour ingress from its other side by a layer of impervious PVC. We did not attempt to use the coating around complex corners. Some delamination was eventually observed on the exposed end-plies, which the muslin did not cover. We have also used G4 with glass tape to strengthen joints, with similar success. However, we have never used G4 composite in a production pod and we still wouldn’t recommend coating an entire timber pod this way.
Adhesive for Wood
Truly waterproof yet strong adhesives for timber are hard to come by. We have tried the following:
- Semforite. Powdered resin, requires mixing with water before application, so somewhat inconvenient to use. Mixes to paste, or viscous liquid, depending on water content. Requires in excess of 24 hours to fully set. Makes a very strong bond which is genuinely waterproof. Other similar products include Cascamite, although beware recent formulation changes.
- Titebond III. We hear good things about this, but have not yet tried it. More waterproof than Evo-Stik / Titebond II but with different bond characteristics.
- Evo-Stik Weatherproof Wood Adhesive. Recommended only where damp will be occasional and limited. We don’t use this outdoors. Ideal for internal features, shelving, etc. Other similar adhesives include Titebond II.
- Single part polyurethane foaming glue, such as WoodWeld PU. Reasonable results on even poorly-made joints but can be messy to use. Other similar adhesives include Gorilla Glue.
- West System 105/205 epoxy. We use this for many external joints in marine plywood-to-plywood structures. Reasonably effective even though it seems not to gain significant penetration into the timber. Often used with stitch-and-glue techniques, too. Very low surface tension so is difficult to keep in the joint during cure, unless joint tolerances are very close. Can be mixed with fillers to make a paste, although this can affect colour and reduce bond strength. PPE: vinyl (not latex) gloves are recommended.
- Soudal Fix-All. To bond non-porous substrates – aluminium sheet bonded to pre-G4’d marine plywood, for example. This works extremely well even for outdoor exposed joints, provided there are large bond areas. This also bonds uncoated timber-to-timber extremely well, but we haven’t tested such uncoated joints subsequently exposed to water. This type of adhesive is superb for large-surface-area joins but is unlikely to be useful for small, detailed joints. There are other brands producing similar adhesive, but they are generally more expensive.
- G4. On previously uncoated plywood structures bonded with (say) epoxy, we find that varnishing copiously with G4 allows it to soak into the timber joints and further improve the strength of those joints. We have even pre-assembled some – non-critical – items and used a generous coating of G4 as a one-hit varnish-and-glue on those items, although we wouldn’t recommend this for critical structures.
- Polyester resin. Not recommended.
Joining plywood sheets
To joint sheets of plywood edge-to-edge with adhesive to create a larger sheet – typically from 18mm ply in order to make a wider floor – there are two common methods:
- If CNC is available, then the two sheets can be shaped to interlock. These can be laid flat on bearers allowing access to the underneath. The underside of the joint can then be sealed closely with a quality masking tape. Temporary clamping pieces, made or covered with non-stick material, can be screwed across the joint at intervals to hold the sheets exactly flush with each other. Epoxy resin can then be poured or syringed into the joint. The resulting joint is far from invisible, unless the board is painted, but it will have a flat surface both sides.
- In a more basic home workshop, the two sheets can be simply laid touching edge-to-edge and absolutely flush with each other. Glass tape can be applied, with epoxy, on one side. Typically a 25mm tape followed immediately – while the epoxy remains at least tacky – with 50mm tape. Once cured, the boards can then be flipped over and the process repeated. Beware that epoxy will seep and drip through the joint and bond the sheets to whatever is below so, again, sealing the underside with masking tape and using non-stick clamping pieces is essential while gluing the glass on the first side. The resulting joint is neither invisible nor completely flat. But for, say, the floor this is unlikely to be especially important.
For either of these methods, the clamping pieces are easily made from timber offcuts covered with heavy polythene tape (sold for mending polytunnels). Screw these directly to the boards with thin woodscrews, and fill the holes after.
With either method, it is better to cut the boards to the desired finished size before jointing: flipping an 8′ x 8′ sheet without injury to oneself or to the part-made joint, would seem nearly impossible.
Strip-Built
Strip-building is a technique used in small boatbuilding, where timber laths – typically 20mm thick – are bent around temporary formers and edge-glued to each other. It lends itself to building complex curves (that is, panels which curve in more than one direction) but can also be used to create flat panels and simple curved roofs. Typically, the laths are cut from western red cedar which is a light but highly durable timber.
The end result is extremely beautiful, especially if laths of differing shades are used. As a consequence, strip-built boats are almost invariably finished with a clear coating, rather than painting.
There are many books, and online resources, which cover strip-building. So we’ll not go into details of the method here.
Strip-building can result in a very light structure. However, this generally requires that the structure is single-skin and is entirely self-supporting without framing elements. This would mean that large, flat panels should be eliminated from the design, as these do not lend themselves well to frameless construction. Therefore a design which uses curves – and even compound curves – for roof and walls might be more appropriate to this construction method.
Unfortunately, though, a single-skin strip-built pod would suffer from poor insulation. Internal insulation could be fitted, but this has all the drawbacks noted further up this page.
To overcome these issues, it might be possible to build SIPs (see below) with, perhaps, a ply or PVC layer on the inside and a strip-build layer on the outside. Adhesive would need to be chosen with care: it must be waterproof, capable of bonding timber-to-timber, and timber-to-PIR, and it must be clear – or white or pale brown – when cured, so as not to spoil the finish. Any weight savings enjoyed from using strip-building would be negated by the double-wall construction, however.
Usually, any completed strip-built boat is sheathed in a thin layer of GRP, to waterproof and strengthen it, and to give it protection against scuffing on beaches and roof-racks. Typically, glass tissue and epoxy resin are used for this. The lack of UV resistance of this epoxy is generally not an issue on small boats as they will be stored indoors. A teardrop is much more exposed to the sunshine and would require a UV-proof coating, which may entirely rule out GRP. Other composite coatings are available but a teardrop might not require an exterior composite coat at all – it may even be beneficial to leave the timber with more opportunity to breathe.
If building a classic-teardrop then strip-building could lend itself well to construction of the outer layer of a curved teardrop roof while other, simpler materials are used for the flat floor and walls.
Before settling on strip-build, do check the prices of laths. In the UK, at least, they are eye-watering.
SIPs
SIPs are Structural Insulated Panels, increasingly used in modern housebuilding. Generally made with a layer of PIR insulation (see PMF, below) sandwiched between two sheet timber products and glued together over the entire surface. The result of this bonding is that the sandwich assembly is stiffer than the sum of the three separate components. The timber layers can therefore be thinner and lighter than they would be in a similar twin-wall construction, and no studs or noggins are required, saving material weight and cost. In addition, the continuous layer of PIR results in better insulation compared to a regular twin-wall construction, and with no cold-spots.
Panels are unlikely to be commercially available in thicknesses and weights appropriate to a teardrop. In any case, panels are not generally sold individually by the building trade – they are mostly manufactured in whole-house sets, each panel potentially unique, so that they assemble somewhat like a jigsaw to make a specific designed house. But the home teardrop builder can make their own SIPs from, for example, layers of 4mm marine ply and 40mm PIR board.
SIPs can be ideal for building flat elements, such as floors and walls. But are more difficult to use for a curved roof.
If using for a floor, ensure that internal framing is fitted between the ply layers wherever strong points are needed (where clamping through the floor onto the chassis, for example). Internal braces will also need to be placed at intervals and/or the ply layers will need to be thicker, to prevent the PIR inside the floor being crushed when the trailer is occupied or loaded.
When using for a wall, a previously made 8×4 SIP sheet could be subsequently cut to make an opening, and then some of the insulation around the opening could be removed to allow a solid timber frame (of PSE) to be set into the gap, ready to accept a window or door. However, this would be difficult to do accurately, and is very messy. A neater and stronger alternative is to build the SIP up layer-by-layer: so machine the inner and outer boards to the shapes required, complete with openings, then fit the window and door frames on one of the panels, then infill with PIR board that has also been cut to shape, and finally bond the outer second layer.
A slightly curved roof might be possible to make as a SIP: the thin ply layers will be moderately flexible, and the PIR itself can be made ‘bendy’ by slicing it across its width at intervals, and/or by using multiple thin layers of PIR bonded together. If the outer layer of the SIP is strip-built, the curve will be slightly easier to form.
There is no need for the inner and outer layers of a SIP panel to be identical. For example, where there is a ventilator the inner layer of ply may have the opening higher than the outer layer does, so that any water falls away to the outside. Or the outer layer at the bottom of a wall might extend further down than the inner layer, so that the panel sits neatly onto the floor when jointed, allowing the outer layer of the wall to be bonded to the side of the floor. Forming SIPs in such a sophisticated way, though, would generally require use of CNC for accuracy.
As with twin-wall construction, some features can be installed within the SIP:
- Wiring can run in grooves routed into the insulation. But beware that cables must be heavily downrated when partially insulated in this way, or they will melt their insulation and risk starting a fire.
- Stainless-steel mesh can be installed between two of the layers at openings for ventilators, as insect barriers.
- Fixed glazing, if any is required, can be installed on the inner side of the outer layer of ply.
A key requirement for home-making SIPS is to source timber framing and PIR board which are near-identical in thickness, so that the insulation and the frames inside the sandwich are equal in thickness. PIR comes in many thicknesses, although beware that the actual thickness may vary from that stated. Most timber yards – and even some builders merchants – are happy to make up PSE to any exact size you specify. So, in general, it is best to source the PIR boards first, then have PSE machined to the thickness you require.
In this section we’ve assumed that any home-made SIP will by ply-PIR-ply construction. But, as in the building trade, other SIPs constructions might be possible. An ideal combination for teardrop making might seem to be birch ply inner layer, PIR, and aluminium outer layer. The challenges with forming, bonding, and detailing such a construction should not be underestimated, however. Not to mention the possible thermal stresses and distortions caused by aluminium expanding far more than birch ply when heated.
Stitch-and-glue
At least one teardrop kit uses the stitch-and-glue method, originally pioneered for dinghy building. This creates a strong, rigid shell from a number of separate thin plywood pieces. The pieces are edge-jointed by stitching them together with twists of copper wire, then gluing with epoxy and glass tape.
The resulting shape of the finished kit is… somewhat wild, with many facets and edges. It has to be, because lightweight stitch-and-glue does not perform well with large, flat panels.
If designing your own stitch-and-glue pod then follow (boatbuilding) design practice:
- Build up the pod from multiple facets of thin plywood, each slightly bent onto a curve. The thin ply is light, but the curve gives it stiffness. Having panels meet at chines (angled edges), adds strength.
- Creating a complete box section along the length of the structure makes the entire creation rigid. On a dinghy that would be the side tanks. But on a pod the ‘box’ would be the entirety of the pod skin itself, so it is important that the doors are not so large as to weaken that box.
By far the hardest part of stitch-and-glue design is working out the shape of each panel: any two panels that meet will each have a curved edge, so that when pulled and stitched together both panels are forced into a curve, and the join creates a chine.
Building a cardboard prototype is one way to make a set of templates. Alternatively, increasingly sophisticated programs such as Fusion360 – which is free for hobby use – may be able to create the designs and output templates.
PMF and XPS or EPS
PMF stands for ‘poor man’s fibreglass’ which is a method of applying a reasonably water-resistant – and modestly structurally useful – fibre-plus-bonder composite coating onto many types of substrate. The fibre in this case being cotton cloth and the bonder being PVA.
XPS is eXtruded PolyStyrene. EPS is Expanded PolyStyrene, more commonly known by one of its trade names, Jablite. Both are available as large, inexpensive, non-structural foam boards used in the building trade for insulation. Both can be used as the substrate, with a PMF coating, to create a teardrop.
Polystyrene is rapidly dissolved by many types of paint and resin. Which is why PVA is usually chosen as the bonder for PMF when building with XPS or EPS.
Other foam products are available, including PIR and, possibly, PUR.
Timber framing is usually required to form openings, and sometimes to stiffen the structure.
There are so many PMF teardrop projects documented online, that we won’t try to say much more here. Look them up: many are extremely inspiring and the method is highly suited to teardrop construction even by novices.
Some few pitfalls of PMF worth noting:
- PMF should not be used as a method of waterproofing. PMF/XPS construction relies on the XPS to prevent water ingress, while the PMF outer (and possibly inner) layers only provide stiffness, strength, and a good substrate for painting. So applying PMF onto, say, an existing plywood pod to address the problems of damp ingress will not prevent the plywood becoming damp.
- The largest XPS sheets available (in the UK) are 2500x600mm and, in some areas of the country, only 1250x600mm. So joints will be required.
- PIR foam insulation boards are available in larger sizes, but PIR is not as good for PMF construction because it is not fully waterproof and will absorb some water. How much water, is somewhat debated in various forums although some of that discussion may be confusing PIR and PUR. PIR sheets most usually are pre-coated in foil, which may affect the PMF bonding.
- EPS likewise is available in larger sizes. It is slightly less insulating, weaker, and – like PIR – is more prone to water absorption.
- Foam boards can burn – fiercely. EPS and XPS are primarily intended for installation underneath poured concrete or screed, where fire performance is not an issue. Some boards may be manufactured with fire-retardents. Fire risk should be a primary factor in deciding which foam board to employ.
- Making a curved XPS roof is challenging. But does not seem impossible. Using, for example, multiple short lengths of thick board and shaping afterwards, or installing multiple thin layers onto the roof to build up the thickness.
- PMF may appeal because it is cheap and so possible to go through multiple prototypes without great cost. However, disposing of each failed PMF prototype may be a little challenging: the local tip is likely to assume you’re a builder, and so charge for disposal (though fees are generally very modest).
This method of construction has a lot going for it. For a start, the weight of the pod is minimal, levels of insulation are phenomenal, and there is an elegant simplicity in using a single material for both the structure and the insulation.
Fibreglass
A few homebuilt fibreglass pods have surfaced on the web, over the years. Usually spotted on auction sites as part-complete projects. We’ve never seen a completed one. The challenges of forming the shape, then finishing the cut edges and fitting-out, seem almost insuperable for the home builder. The end result will still be a single-skin pod which requires insulating to make it habitable.
See also the notes on polyester and epoxy, above.
Several GRP kit and pod manufacturers have popped up – and seemed to have vanished – in the UK, offering completed trailers or kits. Some of them have been elegant and impressive and completed examples of these are frequently seen in use, on forums. Uncompleted kits occasionally surface on auction sites.
If working on an existing (polyester) GRP pod or kit, any additions and alterations are best made using epoxy resin, rather than polyester resin. Epoxy bonds better than polyester (even to polyester) and has far less lingering smell.
Glazing plastics
The safe, legal, and practical choice for DIY glazing plastic to use on vehicles is clear hard-coated polycarbonate. This can be obtained, cut-to-size and E-marked, from a small number of suppliers in the UK. 5mm thickness is typically used. Thicker may be appropriate for especially large glazed areas, or for glazing on the front of the trailer where it may be subject to more buffeting while traveling. Thinner may be required if the glazed area is to be curved.
When having plastic E-marked, specify where on the part that the E-marking should be positioned. Or, at the very least, explain to the supplier how much of the margin of the sheet will be covered by the framing so that they can position the E-marking appropriately. The E-marking must be visible on the finished trailer.
Sealing tape
A typical installation will see the clear plastic bonded directly to the inner (or sometimes outer) face of the outer skin of the trailer. While there are liquid and paste adhesives which will readily bond plastic, they are difficult to use without overspill onto the glazed area. The most practical long-term method of bonding we have found, which makes the joint fully watertight, is Hodgson Flexistrip tape. This tape seals well but, being butyl based, will never set hard and should not be relied on to hold the glazing in position by itself. The glazing will therefore need to be mechanically attached, as well.
Commercial Fittings
Doors and windows
A few specialist doors and windows are manufactured for teardrops (and horse boxes, and similar box-trailers). They are invariably expensive.
Secondhand are often sought out by budget-conscious builders, but then the teardrop design ends up being compromised to suit the fittings. And, if fitting two doors, there’s little hope of finding a matching pair. Builders also often press into service fittings designed for other purposes.
Glazed yacht hatches are a possible choice for doors. These, however, tend to be very expensive and often heavy. While they will certainly have safety glazing, they may not be marked with the necessary approval for road usage. They are also very likely to be heavily tinted, which will create a gloomy interior.
Cutting down secondhand caravan doors is a popular method to create a teardrop door. Again, finding a pair – especially a left-hand/right-hand pair – may be difficult.
Using top-hung caravan windows, rotated 90 degrees, is another possible method of creating a door. Some caravan windows are however surprisingly fragile. Some – especially older ones picked up secondhand – may also be designed for the hinged edge to be protected by an overhang that prevents water ingress. A teardrop door will generally need to open through 180 degrees, so it can lay flat against the outside wall. Top-hung windows may not have hinges which allow this. Most, in any case, won’t have an outside handle as standard, so this will have to be engineered.
A fixed (non-opening) window can be created by bonding a portion of E-marked clear plastic onto the inside of the external wall, and framing around it on the interior. This can be both elegant and reasonably affordable but having the plastic cut and E-marked will still cost many tens of pounds. The funds may be better spent toward a commercial opening window.
Bonding other ‘found’ items to create interesting glazing features – we have seen plastic mixing-bowls, for example – into the sides may be aesthetically appealing. But they won’t be E-marked and so cannot be used if the trailer is to have an IVA.
Any bought-in door or opening window should be carefully assessed for its ability to keep out water including driven rain and spray while traveling.
Exterior vents
Commercial vents are only modestly expensive. A wide variety designed for yachts and caravans – and even residential use – are available. Most plastic grilles have an option for a built-in mesh to keep out insects. Stainless grilles will usually require a separate purchase of mesh, to be installed separately. Beware cheap stainless louvres from generalist suppliers which often have those louvres so little formed that the ventilation is highly restricted: better versions, at slightly higher prices, are available from genuine yacht or caravan suppliers.
Rooflight shutters or blinds
Fixed rooflight glazing – fitted to allow stargazing – will require a night-time shutter. Bespoke blind suppliers would be delighted to take your money. But a cheap tambour door can make a lightweight, compact, and elegant blind, particularly if the rooflight is in a curved roof. A light-coloured one will help reflect away solar heat, during the day.
Awnings
There are several options for an awning:
- Wind-out / roll-out type, as fitted to campervans. Heavy, only provide shade and protection to keep rain from above – not blown rain from the sides. But convenient to use.
- C-Channel, as commonly fitted to caravans. A ready-made awning to slot into this may not be available – many are manufactured to fit specific caravan models and even the generic ‘porch’ type may be far too tall. Slow to set up. Awnings manufactured for caravanning use can be heavy.
- Tent porch extension. Usually manufactured to fit specific family-style tent models but many are easily adapted for use against the side of a teardrop. May use poles, hoops, or air-beams. Moderate setting-up required. Popular. Enclosed types can provide a second ‘room’. Generally less heavy than caravan awnings.
- Hike-tent porch extension. Commonly used on classic-teardrop and on wedge shapes, provided they are not tall. Unlikely to fit a square-topped trailer. Extremely lightweight. Provide shelter from above and sides. Won’t withstand high winds. Very quick to set up.
- Tarp. Stretched between teardrop on one side and car on the other side. Certainly the lightest option. A nuisance to set up and take down each time the car is used. If fastened at four corners, likely to catch and puddle rainwater. Will become noisy in high winds.
- Gazebo. Free-standing structure which can be used as a separate outdoor space, creating, for example, a roofed-over space between the teardrop side and the car hatchback. Popular with all types of campers, not just teardroppers. Some types erect like a tent, using hoops. These are lightweight but slow to pitch and strike. Others fold open with little or no other assembly required. These are heavy but quick to erect.
Fasteners and Small Fittings
Any teardrop stored outdoors (even under cover) will spend much of its time slightly damp, and with the interior at high humidity. Any fasteners, and also small fittings such as hinges, latches, hooks, and eyes, should be resistant to corrosion.
Two distinct types of metal corrosion affect teardrops.
- Direct corrosion of a metal item which is jointing or attached to non-conducting material such as plastic or timber. Steel is the most prone to this. For example steel woodscrews in timber.
- Galvanic corrosion of two metal items which are attached to each other, making electrical contact. All metals are prone to this, the most common instance being aluminium fasteners or sheet in contact with a steel frame.
Direct corrosion can be overcome by using corrosion-proofed fasteners and fittings:
- BZP (bright zinc plated). A very thin layer of zinc – silver or yellow coloured – is deposited on the surface of steel parts during manufacture. This will hold off corrosion for a few weeks or months. After that the underlying steel will rust quickly. Avoid using these on a teardrop if at all possible. Some fasteners (barrel nuts for example) are not widely available in any other material so the builder must compromise if using these.
- Galvanised or sheradized. These processes coat the fastener or fitting with a heavy layer of zinc, giving much more protection than BZP. However, few fasteners are treated this way and, in general, only very heavy duty fittings such as suspension and chassis parts.
- Stainless-steel. Available in two grades, A2 (304) and A4 (316). A4 has better corrosion resistance but either will be sufficient for most teardrops. Stainless fasteners are generally weaker than steel/BZP. Stainless woodscrews, for example, are easily sheared off during insertion if not careful. Small stainless fittings manufactured for dinghies – such as hooks and eyes – are readily available.
- Plated alloys. Items such as door latches, and even hinges, are frequently made from a cast alloy plated with chrome or other bright metal. These are reasonably resistant to corrosion, although in time cosmetic defects will appear as the underlying alloy corrodes in spots and lifts the chrome. Beware cheaper items which may use steel for hidden critical parts such as latch springs – when that steel corrodes the part will fail. Reputable parts for yachts, dinghies, and caravans are likely to be sufficiently durable.
- Plastic. Glass-filled-nylon fittings, such as latches, are widely available, these may be appropriate in some low-stress applications but, again, check for hidden steel parts. Strong plastic fittings manufactured for dinghies – such as hooks and eyes – are readily available. Nylon nuts and bolts have minimal strength and are unlikely to be useful on a teardrop.
Galvanic corrosion is more pernicious. Careful selection of compatible materials is required to prevent it. For example:
- Aluminium/steel. The most likely source of galvanic corrosion on a teardrop comes from fastening aluminium to steel or stainless-steel. The parts should be separated by a waterproof non-conducting layer: paint as a minimum for small parts, or a plastic sheet ideally. If rivets are used they should ideally be monel. Stainless fasteners could be used but should be isolated using a coating such as locking adhesive. Aluminium pop rivets should not be used in contact with steel of any kind, and BZP fasteners should not be used on aluminium.
- Aluminium/copper. Aluminium should not be in contact with any copper-based metals, including brass. Brass fasteners or fittings should not be used on aluminium.
- Aluminium/fittings. Any metal, or metalised, fittings of uncertain composition (chrome-plated cast alloy lights, for example) should be isolated if fitted to an aluminium skin – in a similar way to fastening stainless-steel to aluminium.
- Stainless fittings/fasteners. Stainless-steel fittings, fastened to a non-metallic substrate (e.g. timber) should be attached using stainless-steel fasteners.
Imperial vs metric
Imperial woodscrews are still widely available in the UK, except in smaller sizes under 1″ which are frequently substituted by suppliers with metric ones approximately the same size. Imperial are generally part-threaded, so have an unthreaded shank for a short distance below the head.
Metric woodscrews are also widely available in the UK. In the sizes used by a teardrop builder they generally are full-threaded – an exception being Torx-headed metric screws.
We find that (part-threaded) imperial screws are far less prone to shearing off their head during insertion than (full-threaded) metric. This is particularly true for stainless, which are weaker.
For smaller sizes, stainless self-tapping screws can often be substituted for woodscrews, particularly when attaching thin fittings onto timber. We find them stronger and much less prone to shearing.
Storing a Teardrop
UK weather will affect teardrops in two ways:
- Most teardrop pods will suffer if left long-term in sunlight. All timber paints and varnishes degrade in UV. Rubber seals gradually perish. Plastic glazing may yellow. Frequent hot/cold cycles – exacerbated by being in direct sunshine – cause movement and breakdown of joints.
- Almost all teardrops are highly vulnerable to long-term damp. Even if stored out of the rain, mould will still grow on any timber and soft furnishings if the trailer is stored in still, humid conditions. Metals will corrode or dull in high humidity or – worse – condensation. All timber sheet products – except for marine ply – will delaminate in such conditions.
The ideal storage should therefore be shaded and have low humidity. A location with frequent air-changes is better than one with no air movement. Many teardrop owners have limited storage options. Here’s how to make the most of what you have, to maximise the life of your trailer.
Inside a building
Storing in a building may seem hands-down to be the best option. But only if that building is clean, dry, and well-ventilated will it be a good storage location. Typical examples are:
- Garages and lock-ups. A modern home garage, or a well-built and dry rented lock-up, should be fine.
But many lock-ups – especially older examples – have poorly maintained roofs, no power, no damp-course in the floor, porous walls, no sill to prevent water ingress under the door, and nil ventilation. As a consequence the air inside can be very still and very humid – the absolute best conditions for the propagation of mould.
Most lock-ups are rented and tenants likely forbidden from making improvements, such as fitting ventilation. If power is present, a dehumidifier will create suitably dry conditions for teardrop storage – but they are expensive to run and only the ‘adsorption’ types (which are more expensive to run than ‘compressor’ types) work well in cooler conditions.
Laying a heavy waterproof tarpaulin over the entire floor can partially compensate for lack of a damp-course, and will substantially reduce humidity if that is the main source of damp in the building. - Timber garden shed or lightweight garage. Most garden sheds will – initially – have all the drawbacks of a leaky lock-up. However, the user is more likely to have options to make some modifications. Adding a large amount of ventilation – multiple static vents and/or some forced extract – can hugely reduce humidity and risk of mould.
- Shipping container or lorry body. Much the same as a garden shed, plus will suffer from high temperatures if in full sunshine. Lorry body roofs are often transparent and admit UV.
- Temporary garage. Tent-like structures, widely available for a few hundred pounds. They can be a very good option. The ‘garage’ should be sited in an open airy location – not in a windless tight corner. The floor (ground) should be covered with a heavy tarpaulin to both suppress plant growth and to act as a damp-course. The skirt should be permanently lifted, and kept free of long vegetation, so that air can freely flow underneath (mesh can replace it, to keep out animals, if necessary).
- Carport. In combination with a breathable cover (see below) would usually be fine: the carport keeps the rain off, the cover keeps the sun off, and there is plenty of ventilation.
- Barn. If storing in a barn – either on an active farm or a disused one – a key concern is chemical corrosion. Lime is highly corrosive even in dry powder form and will be carried on, and despoited by, even light air currents. Other fertilisers, including manure, can be problematic but are less likely to waft on air-currents and would require damp to promote significant corrosion.
Under a cover
There are several types of fabric cover:
- Framed folding non-contact cover. These are generally more expensive than a temporary garage. In all other respects they offer a similar storage environment, but seem on the whole less practical, likely to wear out more quickly, and more prone to storm damage.
- Breathable fabric contact-cover. Use with caution. The cover will hold liquid water against the roof pretty much permanently during a typical UK winter. If the trailer won’t be damaged by such direct contact, then a breathable cover does a good job of cutting UV exposure and – if externally silvered – will reduce day/night thermal cycles. As an example: our own demo PhieldBug (plywood sides, unpainted ally roof) has lived outdoors year-round under a Halfords ‘all-season’ 3-layer breathable car cover. There’s been no significant damp or UV damage even after several years and, despite being in a windy location, there’s been no significant wear from moving fabric.
- Non-breathable fabric cover. We wouldn’t recommend it: the cost saving over a breathable cover is minimal, but the risk of water damage much increased.
- Inflatable storage. Covers which are sealed around the vehicle and then inflated by air-pumps (sometimes with dehumidified air). May be indoors or outdoors types. It’s a lot of trouble and expense to go to, isn’t it? Air-pump noise may be intrusive. Probably better to buy, or build, a less vulnerable teardrop that can be stored without such pampering.
With any over-the-top fabric cover, it is essential to: cover the ground underneath the trailer with a heavy tarpaulin to reduce evaporation and to suppress plant growth; to leave plenty of ventilation space around the skirt of the cover; and to park the covered trailer in a breezy location to prevent stagnation of the air.
Unprotected
Some teardrops, particularly GRP ones, may be fine if stored unprotected. Regular washing will reduce mildew and moss buildup. Storing in an airy location will help ventilate the interior (via the trailer’s permanent vents) and prevent internal mould. Occasional waxing, if appropriate, will reduce – or at least hide – surface degradation.
Pre-Storage
Before packing a teardrop away into storage:
- Remove any tinned food, fresh water, or waste water, any of which might freeze or leak and cause damage.
- Disconnect batteries. And make necessary arrangements to maintain them: lead-acid should be charged regularly as they degrade when allowed to self-discharge; Lithium should be set to ‘storage charge’ level after which they will likely not need any attention for many months.
- Remove any gas canisters – including disposable types – unless the storage location is both well ventilated and guaranteed not to overheat.
- Likewise remove any pressurised aerosols – deodorants etc. These use flammable gas as propellant which may leak if the can rusts, or if exposed to high temperatures, or even if accidentally operated.
- Ensure mice, rats, and birds have no access to the interior and particalarly not to any soft furnishings or exposed wiring and hoses.
End Note
Thanks for reading. We hope some of this has been useful and that we haven’t wasted your time. Sorry that we haven’t used pictures but creating and maintaining a website requires a lot of round tuits, and we just don’t have enough to spare.
If you came here looking for answers, and we failed to give them… do get in touch. You might ask something we know about but forgot to mention, in which case we’ll send you the answer and add it to this page.
If we’ve said something that’s wrong, then please tell us so that we can stop saying it.
If you enjoyed this page, then please consider clicking ‘like’.
Cheers,
PhieldBug